ETSITS101 724V8.0.0 (2000-10) Technical Specification Digital cellular telecommunications system (Phase 2+); Location Services (LCS); (Functional description) - Stage 2 (GSM 03.71 version 8.0.0 Release 1999) Gsm: GLOBAL SYSTEM FOR MOBILE COMMUNICATIONS (GSM 03.71 version 8.0.0 Release 1999) 2 ETSI TS 101 724 V8.0.0 (2000-10) Reference RTS/SMG-030371Q8 Keywords Digital cellular telecommunications system, Global System for Mobile communications (GSM), LCS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N ° 348 623 562 0001 7 - NAF 742 C Association a but non lucratif enregistree a la Sous-Prefecture de Grasse (06) N° 7803/88 Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://www.etsi.org/tb/status/ If you find errors in the present document, send your comment to: editor@etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. © European Telecommunications Standards Institute 2000. All rights reserved. £75/ (GSM 03.71 version 8.0.0 Release 1999) 3 ETSI TS 101 724 V8.0.0 (2000-10) Contents Intellectual Property Rights 8 Foreword 8 1 Scope 9 2 References 9 3 Definitions, abbreviations and symbols 10 3.1 Definitions 10 3.2 Abbreviations 11 3.3 Symbols 12 4 Main concepts 12 4.1 Assumptions 12 4.2 Timing Advance (TA) 13 4.3 Time of Arrival (TOA) positioning mechanism 13 4.4 Enhanced Observed Time Difference (E-OTD) positioning mechanism 13 4.5 Global Positioning System (GPS) positioning mechanism 13 5 General LCS architecture 13 5.1 LCS access interfaces and reference points 13 5.2 LCS Functional diagram 14 5.3 LCS CLIENT 15 5.3.1 LCS Component 15 5.3.1.1 Location Client Function (LCF) 15 5.4 LCS Server 15 5.4.1 Client handling component 15 5.4.1.1 Location Client Control Function (LCCF) 15 5.4.1.2 Location Client Authorization Function (LCAF) 15 5.4.1.2.1 Access Subfunction 15 5.4.1.2.2 Subscription Subfunction 16 5.4.2 System handling component 16 5.4.2.1 LMU Mobility Management Function (LMMF) 16 5.4.2.2 Location System Control Function (LSCF) 16 5.4.2.3 Location System Billing Function (LSBF) 16 5.4.2.4 Location Client Coordinate Transformation Function (LCCTF) 16 5.4.2.5 Location System Operations Function (LSOF) 17 5.4.2.6 Location System Broadcast Function (LSBcF) 17 5.4.3 Subscriber Component 17 5.4.3.1 Location Subscriber Authorization Function (LSAF) 17 5.4.3.2 Location Subscriber Privacy Function (LSPF) 17 5.4.4 Positioning component 17 5.4.4.1 Positioning Radio Coordination Function (PRCF) 17 5.4.4.2 Positioning Radio Assistance Function (PRAF) 17 5.4.4.3 Positioning Calculation Function (PCF) 17 5.4.4.4 Positioning Signal Measurement Function (PSMF) 17 5.5 Information Flows between Client and Server 17 5.5.1 Location Service Request 18 5.5.2 Location Service Response 18 5.6 Logical architecture 18 5.6.1 BSS 19 5.6.2 LCS Client 19 5.6.3 GMLC 19 5.6.4 SMLC 19 5.6.5 MS 20 5.6.6 LMU 20 5.6.7 MSC 21 5.6.8 HLR 21 £75/ (GSM 03.71 version 8.0.0 Release 1999) 4 ETSI TS 101 724 V8.0.0 (2000-10) 5.6.9 gsmSCF 21 5.6.10 LMU and SMLC association 21 5.7 Embedded Architecture 22 5.8 Assignment of functions to general logical architecture 23 6 Signalling Protocols and Interfaces 23 6.1 Generic Signalling Model for LCS 23 6.1.1 Protocol layering 23 6.1.2 Message Segmentation 24 6.1.2.1 Intermediate Level Segmentation 24 6.1.2.2 Network Level Segmentation 25 6.2 Signalling between an SMLC, MSC and BSC 25 6.3 SMLC Signaling to a Target MS 26 6.4 SMLC Signalling to a Type A LMU 26 6.4.1 Signalling using an SDCCH 26 6.4.2 Signalling using a TCH 27 6.5 SMLC signaling to a Type B LMU 28 6.6 SMLC Signalling to a peer SMLC 29 7 General Network Location Procedures 31 7.1 State Description for the GMLC 31 7.1.1 GMLC States 31 7.1.1.1 NULL State 31 7.1.1.2 INTERROGATION State 31 7.1.1.3 LOCATION State 31 7.1.2 State Functionality 31 7.1.2.1 State Transitions 31 7.1.2.2 INTERROGATION Timer Function 32 7.1.2.3 LOCATION Timer Function 32 7.2 State Description for the VMSC 32 7.2.1 VMSC States 32 7.2.1.1 IDLE State 32 7.2.1.2 LOCATION State 32 7.2.2 State Functionality 33 7.2.2.1 State Transitions 33 7.2.2.2 LOCATION Timer Function 33 7.3 State Description for the BSC 33 7.3.1 BSC States 33 7.3.1.1 IDLE State 33 7.3.1.2 LOCATION State 34 7.3.2 State Functionality 34 7.3.2.1 State Transitions 34 7.3.2.2 LOCATION Timer Function 34 7.4 State Description for the SMLC 35 7.4.1 SMLC States 35 7.4.1.1 NULL State 35 7.4.1.2 LOCATION State 35 7.4.2 State Functionality 35 7.4.2.1 State Transitions 35 7.4.2.2 LOCATION Timer Function 36 7.5 Usage of SCCP Connections on the Ls and Lb interfaces 36 7.5.1 SCCP connection for positioning of a target MS 36 7.5.2 SCCP connection to access a type A LMU 37 7.6 General Network Positioning Procedures 37 7.6.1 Mobile Terminating Location Request (MT-LR) 38 7.6.1.1 Location Preparation Procedure 38 7.6.1.2 Positioning Measurement Establishment Procedure 40 7.6.1.3 Location Calculation and Release Procedure 40 7.6.2 MT-LR without HLR Query - applicable to North America Emergency Calls only 40 7.6.3 MT-LR for a previously obtained location estimate 41 7.6.3.1 Initial Location 41 7.6.3.2 Current Location 42 £75/ (GSM 03.71 version 8.0.0 Release 1999) 5 ETSI TS 101 724 V8.0.0 (2000-10) Last known Location 42 Security and Privacy 42 Failing to locate the target MS 42 Target MS is 'Not Reachable' 42 Target MS is 'Detached' 42 Target MS is Reachable but Positioning Fails 43 Target MS is 'Purged' 43 Network Induced Location Request (NI-LR) 43 Location Preparation Procedure 44 Positioning Measurement Establishment Procedure 44 Location Calculation and Release Procedure 44 Network Induced Location Request (NI-LR) from a Serving BSC for a target MS in dedicated mode 45 Location Preparation Procedure 45 Positioning Measurement Establishment Procedure 45 Location Calculation and Release Procedure 46 Mobile Originating Location Request (MO-LR) 46 Location Preparation Procedure 47 Positioning Measurement Establishment Procedure 47 Location Calculation and Release Procedure 47 Common Procedures to Support Positioning 48 Information Transfer between an NSS based SMLC and a Target MS 48 Information Transfer between a BSS based SMLC and a Target MS 49 Information Transfer between an NSS based SMLC and a BSC 50 Information Transfer between a BSS based SMLC and a BSC 51 Common Procedures to Support Access to an LMU 51 Information Transfer between an NSS based SMLC and a Type A LMU 52 Information Transfer using an SDCCH 52 Information Transfer using a TCH 53 Location Update Procedure between a BSS based SMLC and a Type A LMU 54 IMSI Detach Procedure between a BSS based SMLC and a Type A LMU 55 LCS Information Transfer between a BSS based SMLC and a Type A LMU 56 Information Transfer using an SDCCH 56 Information Transfer using a TCH 57 Information Transfer between an NSS based SMLC and a Type B LMU 58 Information Transfer between a BSS based SMLC and a Type B LMU 59 Common Control Procedures for LMUs 59 Reset Procedure 60 Status Query Procedure 60 Status Update Procedure 60 Common Procedures supporting Interaction between Peer SMLCs 61 Information Transfer between Peer SMLCs 61 Exception Procedures 62 Procedures in the SMLC 62 Procedures in the VMSC 63 Procedures in an LMU 63 Procedures in the BSC 64 General Procedures 64 Rejection of an SMLC Positioning Request 64 Interaction with Inter-BSC or Inter-MSC Handover 64 Interaction with Intra-BSC Handover and other RR Management Procedures 64 Priority of Handover and Other RR Management Procedures 64 Interaction with Segmentation 65 Overload 65 Procedures in the Target MS 65 Further Procedures for Handover 65 MSC procedure for Inter-MSC Handover 65 Handling of an ongoing handover while a request for positioning arrives at MSC/VLR 65 Privacy 65 Privacy Override Indicator (POI) 65 Privacy Procedures 66 MS Privacy Options 66 Mobile Originating Location 68 £75/ 7.6.3.3 7.6.3.4 7.6.3.5 7.6.3.5.1 7.6.3.5.2 7.6.3.5.3 7.6.3.5.4 7.6.4 7.6.4.1 7.6.4.2 7.6.4.3 7.6.5 7.6.5.1 7.6.5.2 7.6.5.3 7.6.6 7.6.6.1 7.6.6.2 7.6.6.3 7.7 7.7.1 7.7.2 7.7.3 7.7.4 7.8 7.8.1 7.8.1.1 7.8.1.2 7.8.2 7.8.3 7.8.4 7.8.4.1 7.8.4.2 7.8.5 7.8.6 7.9 7.9.1 7.9.2 7.9.3 7.10 7.10.1 7.11 7.11.1 7.11.2 7.11.3 7.11.4 7.11.4.1 7.11.4.2 7.11.4.3 7.11.4.4 7.11.4.5 7.11.4.6 7.11.4.7 7.11.5 7.11.6 7.11.6.1 7.11.6.2 7.12 7.12.1 7.12.2 7.12.3 7.13 (GSM 03.71 version 8.0.0 Release 1999) 6 ETSI TS 101 724 V8.0.0 (2000-10) 7.14 CM Procedures 68 7.14.1 Location request for a mobile in idle-mode 68 7.14.2 Location request for a mobile in dedicated-mode 68 7.15 Radio Interface Timing Procedures 68 7.15.1 LMU Functions 69 7.15.2 SMLC Functions 69 7.15.3 LMU-SMLC Interactions 69 8 TA based Positioning 70 8.1 Definition of TA states 70 8.1.1 MS in IDLE State 70 8.1.2 MS in DEDICATED State 70 8.2 TA Positioning Procedure for an NSS based SMLC 71 8.3 TA Positioning Procedure for a BSS based SMLC 71 8.4 Unsuccessful TA positioning procedure in BSC 72 9 TOA based positioning 73 9.1 TOA procedures 73 9.1.1 Successful TOA Positioning Procedure for NSS based SMLC 73 9.1.2 Successful TOA Positioning Procedure for BSS based SMLC 75 9.1.3 Successful TOA positioning procedure in BSC 76 10 E-OTD and GPS Positioning Procedures 77 10.1 General Procedures 77 10.2 Positioning for BSS based SMLC 77 10.3 Positioning for NSS based SMLC 77 10.4 Assistance Data Delivery from BSS based SMLC 79 10.5 Assistance Data Delivery from NSS based SMLC 79 10.6 Error Handling for E-OTD and GPS 80 10.6.1 NSS based SMLC 81 10.6.2 BSS based SMLC 82 10.7 Broadcast OF ASSISTANCE DATA 82 10.7.1 Point-To-Multipoint Assistance Data Broadcast Flow 83 10.7.2 Ciphering 84 10.7.3 Algorithm 84 10.7.4 Deciphering key control and delivery to MS 85 11 Position calculation functionality 87 11.1 TA 87 11.2 Time Of Arrival (TOA) Positioning mechanism 87 11.3 Enhanced Observed Time Difference (E-OTD) 87 11.4 Global Positioning System (GPS) positioning mechanism 87 12 Information storage 88 12.1 HLR 88 12.2 VLR 90 12.3 GMLC 90 12.4 SMLC 91 12.5 Recovery and Restoration Procedures 93 £75/ (GSM 03.71 version 8.0.0 Release 1999) 7 ETSI TS 101 724 V8.0.0 (2000-10) 13 Operational Aspects 93 Annex A (informative): Examples of MT-LR 95 A.l PLMN Roles 95 A.2 Non-Call Related MT-LR 95 A.3 Call Related MT-LR 96 Annex B (informative): Description of TOA 98 Annex C (informative): Description of E-OTD 99 C.l Basic Concepts 99 C.2 Position Calculation Types 99 C.3 Implementation Issues 101 Annex D (informative): Description Of Assisted GPS 102 D.l Assisted-GPS 104 D.2 MS-Assisted GPS 105 D.3 MS-BasedGPS 105 D.4 References 105 Annex E (informative): Change History 106 History 107 £75/ (GSM 03.71 version 8.0.0 Release 1999) 8 ETSI TS 101 724 V8.0.0 (2000-10) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards" , which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server ( http://www.etsi.org/ipr) . Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Special Mobile Group (SMG). The present document defines the stage 2 Functional description of Location Services (LCS) within the digital cellular telecommunications system (Phase 2/Phase 2+). The contents of the present document are subject to continuing work within SMG and TlPl and may change following formal SMG and TlPl approval. Should SMG or TlPl modify the contents of the present document it will then be re-issued with an identifying change of release date and an increase in version number as follows: Version 7.x.y where: 7 GSM Phase 2+ Release 1 998 ; X the second digit is incremented for all other types of changes, i.e. technical enhancements, corrections, updates, etc.; y the third digit is incremented when editorial only changes have been incorporated in the specification. £75/ (GSM 03.71 version 8.0.0 Release 1999) 9 ETSI TS 101 724 V8.0.0 (2000-10) Scope The present document defines the stage-2 service description for the LoCation Services (LCS) feature on GSM, which provides the mechanisms to support mobile location services of operators, which are not covered by standardized GSM services. CCITT 1.130 [4] describes a three-stage method for characterization of telecommunication services, and CCITT Q.65 [5]defines stage 2 of the method. The LCS feature is a network feature and not a supplementary service. This version of the stage 2 service description covers aspects of LCS e.g., the functional model, architecture, positioning methods, message flows etc. References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. • A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same number. • For this Release 1998 document, references to GSM documents are for Release 1998 versions (version 7.x.y). [1] GSM 01.04: "Digital cellular telecommunications system (Phase 2+); Abbreviations and acronyms". [2] GSM 02.71: "Digital cellular telecommunications system (Phase 2+); Location Services (LCS); Service description; Stage 1". [3] GSM 03.07: "Digital cellular telecommunications system (Phase 2+); Restoration Procedures". [4] GSM 03.41: "Digital cellular telecommunication system (Phase 2+); Technical realization of Short Message Service Cell Broadcast (SMSCB)". [5] GSM 03.49: "Digital cellular telecommunication system (Phase 2+); Example protocol stacks for interconnecting Cell Broadcast Centre (CBC) and Mobile-services Switching Centre (MSC)". [6] GSM 03.78: "Digital cellular telecommunications system (Phase 2+); Customized Application for Mobile network Enhanced Logic (CAMEL) Phase 3; Stage 3". [6a] GSM 04.06: "Digital cellular telecommunications system (Phase 2+); Mobile Station - Base Station System (MS - BSS) interface Data Link (DL) layer specification". [7] GSM 04.08: "Digital cellular telecommunications system (Phase 2+); Mobile radio interface layer 3 specification". [8] GSM 04.31: "Digital cellular telecommunications system (Phase 2+); Location Services (LCS); Mobile Station (MS) - Serving Mobile Location Center (SMLC); Radio Resource LCS Protocol (RRLP)". [9] GSM 04.71: "Digital cellular telecommunications system (Phase 2+); Mobile radio interface layer 3 Location Services (LCS) specification". [10] GSM 08.08: "Digital cellular telecommunications system (Phase 2+); Mobile-services Switching Centre - Base Station System (MSC-BSS) interface; Layer 3 specification". £75/ (GSM 03.71 version 8.0.0 Release 1999) 10 ETSI TS 101 724 V8.0.0 (2000-10) [11] GSM 08.31: "Digital cellular telecommunications system (Phase 2+); Location Services (LCS); Serving Mobile Location Center (SMLC) - Serving Mobile Location Center (SMLC); SMLC Peer Protocol (SMLCPP)". [11a] GSM 08.58: "Digital cellular telecommunications system (Phase 2+); Base Station Controller - Base Transceiver Station (BSC - BTS) interface; Layer 3 specification". [12] GSM 08.71: "Digital cellular telecommunications system (Phase 2+); Location Services (LCS); Serving Mobile Location Center - Base Station Subsystem (SMLC-BSS) interface Layer 3 specification". [13] GSM 09.02: "Digital cellular telecommunications system (Phase 2+); Mobile Application Part (MAP) specification". [14] GSM 09.31: "Digital cellular telecommunications system (Phase 2+); Location Services (LCS); Base Station System Application Part LCS Extension (BSSAP-LE)". [15] CCITT Recommendations 1. 130: "General modelling methods - Method for the characterisation of telecommunication services supported by an ISDN and network capabilities of an ISDN". [16] CCITT Recommendation Q.65: "Methodology - Stage 2 of the method for the characterization of services supported by an ISDN". 3 Definitions, abbreviations and symbols 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: Location Estimate: the geographic location of an MS and/or a valid ME, expressed in latitude and longitude data. The Location Estimate shall be represented in a well-defined universal format. Translation from this universal format to another geographic location system may be supported, although the details are considered outside the scope of the primitive services. Mobile Assisted positioning: any mobile centric positioning method (e.g. E-OTD, GPS) in which the MS provides position measurements to the network for computation of a location estimate by the network. The network may provide assistance data to the MS to enable position measurements and/or improve measurement performance. Mobile Based positioning: any mobile centric positioning method (e.g. E-OTD, GPS) in which the MS performs both position measurements and computation of a location estimate and where assistance data useful or essential to one or both of these functions is provided to the MS by the network. Position methods where an MS performs measurements and location computation without network assistance data are not considered within this category. Mobile Originating Location Request (MO-LR): any location request from a client MS to the LCS Server made over the GSM air interface. While an MO-LR could be used to request the location of another MS, its primary purpose is to obtain an estimate of the client MS's own location either for the client MS itself or for another LCS client designated by the MS. Mobile Terminating Location Request (MT-LR): any location request from an LCS client where the client is treated as being external to the PLMN to which the location request is made. Network Induced Location Request (NI-LR): any location request for a target MS from a client that can be considered to lie inside any of the PLMN entities currently serving the target MS. In this case, the LCS client is also within the LCS server. Examples of an Nl-LR include a location request needed for supplementary services, for emergency call origination and by O&M in a visited PLMN. North American Emergency Services Routing Digits (NA-ESRD): a telephone number in the North American Numbering Plan (NANP) that can be used to identify a North American emergency services provider and any associated LCS client. The ESRD shall also identify the base station , cell site or sector from which a North American emergency call originates. £75/ (GSM 03.71 version 8.0.0 Release 1999) 11 ETSI TS 101 724 V8.0.0 (2000-10) North American Emergency Services Routing Key (NA-ESRK): a telephone number in the North American Numbering Plan (NANP) assigned to an emergency services call by a North American VPLMN for the duration of the call that can be used to identify (e.g. route to) both the emergency services provider and the switch in the VPLMN currently serving the emergency caller. During the lifetime of an emergency services call, the ESRK can also be used to identify the calling mobile subscriber. 3.2 Abbreviations Certain abbreviations used in the present document are also listed in GSM 01.04. For the purposes of the present document, the following abbreviations apply: ANM Answer Message (ISUP) BSSAP-LE BSSAP LCS Extension for Lb, Lp and Ls interfaces BSSLAP ESS LCS Assistance Protocol BSSMAP-LE BSSMAP LCS Extension CC SCCP Connection Confirm CR SCCP Connection Request CREF SCCP Connection Refused DTI SCCP Data Form 1 message FEC Forward Error Correction lAM Initial Address Message (ISUP) LCAF Location Client Authorization Function LCCF Location Client Control Function LCCTF Location Client Coordinate Transformation Function LCF Location Client Function LDR Location Deferred Request LIR Location Immediate Request LLP LMU LCS Protocol LMMF LMU Mobility Management Function LMU Location Measurement Unit LSAF Location Subscriber Authorization Function LSBcF Location System Broadcast Function LSBF Location System Billing Function LSCF Location System Control Function LSOF Location System Operations Function LSPF Location Subscriber Privacy Function MLC Mobile Location Center MO-LR Mobile Originating Location Request MT-LR Mobile Terminating Location Request NI-LR Network Induced Location Request PCF Positioning Calculation Function PRAF Positioning Radio Assistance Function PRCF Positioning Radio Coordination Function PSMF Positioning Signal Measurement Function RA Rate Adaptation REL Release (ISUP) RLC Release Complete (ISUP or SCCP) RLP Radio Link Protocol (GSM 04.22) RLSD SCCP Released message RRLP RR LCS Protocol to a target MS (defined in GSM 04.3 1) SLPP Subscriber LCS Privacy Profile SMLCPP SMLC Peer Protocol (messages on Lp interface in GSM 08.3 1) TA Timing Advance (between an MS and its serving BTS) TOA Time of Arrival UDT SCCP Unitdata message £75/ (GSM 03.71 version 8.0.0 Release 1999) 12 ETSI TS 101 724 V8.0.0 (2000-10) 3.3 Symbols For the purposes of the present document, the following symbols apply: Lb Interface between Serving MLC and BSC (BSC interface) Lc Interface between gateway MLC and gsmSCF (CAMEL interface) Le Interface between External User and MLC (external interface) Lg Interface between Gateway MLC and VMSC (gateway MLC interface) Lh Interface between Gateway MLC and HLR (HLR interface) Lp Interface between SMLC and peer SMLC (peer interface) Ls Interface between Serving MLC and VMSC (serving MLC interface) Um Air Interface to an LMU (measurement interface) Main concepts LCS utilizes one or more positioning mechanisms in order to determine the location of a Mobile Station. Positioning a target MS involves two main steps: signal measurements and location estimate computation based on the measured signals. Three positioning mechanisms are proposed for LCS: Uplink Time of Arrival (TO A), Enhanced Observed Time Difference (E-OTD), and Global Positioning System (GPS) assisted. 4.1 Assumptions Support an SMLC that can be either BSS based or NSS based. While the SMLC is considered to be a separate logical entity, it may still be physically part of an MSC or BSC. Standardize a similar open interface to the SMLC whether it is NSS or BSS based. This simplifies migration from an NSS to a BSS based location architecture and avoids two different types of SMLC. Support "Type A" LMUs accessed over the GSM air interface using the same signaling protocols for both BSS and NSS based SMLC interaction. A type A LMU supports the RR and MM signaling procedures defined in GSM 04.08. A type A LMU may have a subscription profile in the HLR and may support certain CM services - e.g. outgoing data calls for SW download and SMS for SIM card download. Support "Type B" LMUs accessed over the Abis interface. The LMU may be either free standing (support Abis signaling) or associated with a BTS - either integrated or connected by proprietary means. If free standing, a type B LMU could be identified using a pseudo cell ID. Employ the same application protocol defined in GSM 04.71 for all types of LMU. Use MTP, SCCP, BSSAP as the basis for all LCS signaling between the SMLC, BSC, MSC and (for GPRS) SGSN, since these are the only protocols that are all supported in a BSC, MSC and SGSN. Substitution of TCP/IP or FR could be used in 3G. An important consequence of this change is that TCAP and MAP are no longer needed for signaling to an SMLC (since retention of TCAP and MAP would only be feasible for an NSS based SMLC, thereby producing two distinct types of SMLC). Provide enough flexibility to enable usage of transport protocols other than MTP/SCCP to support LCS for GPRS and 3G. Employ SCCP connection oriented signaling in the NSS and BSS to access a type A LMU or target MS to enable LCS messages to be easily relayed through an MSC and BSC. Add signaling between peer SMLCs to enable an SMLC to request or receive E-OTD, TOA or GPS positioning and assistance measurements obtained by an LMU belonging to another SMLC. Enable migration from an NSS based SMLC to BSS based SMLCs. £75/ (GSM 03.71 version 8.0.0 Release 1999) 13 ETSI TS 101 724 V8.0.0 (2000-10) 4.2 Timing A(jvance (TA) The TA is based on the existing Timing Advance (TA) parameter. The TA value is known for the serving BTS. To obtain TA values in case the MS is in idle mode a special call, not noticed by the GSM subscriber (no ringing tone), is set up. The cell-ID of the serving cell and the TA is returned as the result of the TA. TA is used to assist all positioning mechanisms and as a fall-back procedure. 4.3 Time of Arrival (TOA) positioning mechanism The uplink TOA positioning method is based on measuring the Time of Arrival (TOA) of a known signal sent from the mobile and received at three or more measurement units. The known signal is the access bursts generated by having the mobile perform an asynchronous handover. The method requires additional measurement unit (LMU) hardware in the network at the geographical vicinity of the mobile to be positioned to accurately measure the TOA of the bursts. Since the geographical coordinates of the measurement units are known, the mobile position can be calculated via hyperbolic triangulation. This method will work with existing mobiles without any modification. 4.4 Enhanced Observed Time Difference (E-OTD) positioning mechanism The E-OTD method is based on measurements in the MS of the Enhanced Observed Time Difference of arrival of bursts of nearby pairs of BTSs. For E-OTD measurement synchronization, normal and dummy bursts are used. When the transmission frames of BTSs are not synchronized, the network needs to measure the Relative or Absolute Time Differences (RTDs or ATDs) between them. To obtain accurate triangulation, E-OTD measurements and, for non- synchronized BTSs, RTD or ATD measurements are needed for at least three distinct pairs of geographically dispersed BTSs. Based on the measured E-OTD values the location of MS can be calculated either in the network or in the MS itself, if all the needed information is available in MS. See annex C for a detailed description of E-OTD. 4.5 Global Positioning System (GPS) positioning mechanism The Global Positioning System (GPS) method refers to any of several variants that make use of GPS signals or additional signals derived from GPS signals in order to calculate MS position. These variants give rise to a range of optional information flows between the MS and the network. One dimension of variation is where position calculation is performed: a) MS -based PCF or b) network-based PCF. Another dimension is whether "assistance data" is required - irrespective of where position calculation is performed. Examples of assistance data include differential GPS data; lists of satellites in view based on approximate MS position, etc. A third dimension of variation is closely related to the preceding, namely, the origin and distribution of any assistance data. For example, even while assistance data may be required of a GPS method, it may be optional that the assistance data originates from and is distributed within and by the PLMN, VPLMN, etc. 5 General LCS architecture 5.1 LCS access interfaces and reference points There is one reference point between the LCS PLMN server and LCS client called Le. Le is described in GSM 02.71 however the protocol specifics are for further study. There may be more than a single LCS network interface to several different LCS clients or other networks. These networks may both differ in ownership as well as in communications protocol. The network operator should define and negotiate interconnect with each external LCS client or other network. An interface differs from a reference point in that an interface is defined where specific LCS information is exchanges and needs to be fully recognized. There is an inter-LCS PLMN interface called Lg that connects two independent LCS networks for message exchange. £75/ (GSM 03.71 version 8.0.0 Release 1999) 14 ETSI TS 101 724 V8.0.0 (2000-10) Figure 1 : LCS Access Interfaces and Reference Points 5.2 LCS Functional diagram GSM 02.71 [2] describes the overall LCS service description from the LCS client point of view. In this specification, a more detailed description of LCS is given. The LCS functional diagram shown in figure 2 depicts the interaction of the LCS client and the LCS server within the PLMN. The PLMN uses the various LCS components within LCS server to provide the target MS Location Information to the LCS client. LCS Client Client handling component LC^ LCF, LCF3 LCF„ Location Service Request I Location Service Response Subscriber ■< handling component Resources: GSIVI protocols LCS Server Figure 2: PLMN LCS capability server Functional Diagram £75/ (GSM 03.71 version 8.0.0 Release 1999) 15 ETSI TS 101 724 V8.0.0 (2000-10) 5.3 LCS CLIENT An LCS client contains an LCS component with one or more client(s) which by using location information can provide location based services. An LCS client is a logical functional entity that requests from the LCS server in the PLMN location information for one or more than one target MS within a specified set of parameters such as Quality of Service (QoS). The LCS Client may reside in an entity (including the MS) within the PLMN or in an entity external to the PLMN. The specification of the LCS Client's internal logic and its relation to the external use is outside the scope of this document. 5.3.1 LCS Component 5.3.1 .1 Location Client Function (LCF) The Location Client Function (LCF) provides a logical interface between the LCS client and the LCS server. This function is responsible for requesting location information for one or more MEs/MSs with a specified "QoS" and receiving a response, which contains either location information or a failure indicator. 5.4 LCS Server 5.4.1 Client handling component 5.4.1 .1 Location Client Control Function (LCCF) The Location Client Control Function (LCCF) manages the external interface towards LCF. . The LCCF identifies the LCS client within the GSM PLMN by requesting client verification and authorization ( i.e. verifies that the LCS client is allowed to position the subscriber) through interaction with the Location Client Authorization Function (LCAF). The LCCF handles mobility management for location services (LCS) e.g., forwarding of positioning requests to VMSC. The LCCF determines if the final positioning estimate satisfies the QoS for the purpose of retry/reject. The LCCF provides flow control of positioning requests between simultaneous positioning requests. It may order the Location Client Coordinate Transformation Function (LCCTF) to perform a transformation to local coordinates. It also generates charging and billing related data for LCS via the Location System Billing Function (LSBF). 5.4.1.2 Location Client Authorization Function (LCAF) The Location Client Authorization Function (LCAF) is responsible for providing access and subscription authorization to a client. Specifically, it provides authorization to a LCS client requesting access to the network and authorizes the subscription of a client. LCAF provides authorization to a LCS client requesting Location Information of a specific MS. 5.4.1.2.1 Access Subfunctlon An Access Subfunction enables LCS clients to access LCS services. This subfunction provides verification and authorization of the requesting client. When a LCS is requested, the Access Subfunction uses the information stored in the LCS client subscription profile to verify that: the LCS client is registered; and the LCS client is authorized to use the specified LCS request type; the LCS client is allowed to request location information for the subscriber(s) specified in the LCS request; £75/ (GSM 03.71 version 8.0.0 Release 1999) 16 ETSI TS 101 724 V8.0.0 (2000-10) 5.4.1.2.2 Subscription Subfunction The LCS client Subscription profile shall contain a minimum set of parameters assigned on per LCS client basis for an agreed contractual period. The LCS client profile shall contain the following set of access parameters: LCS client identity; - Allowed LCS request types (i.e. LIR, LDR or both); Maximum number of subscribers allowed in a single LCS request; Priority; Position override indicator; - State(s); Event(s) (applicable to LDR requests only); Local coordinate system; LCS client access barring list (optional); PLMN access barring list applicability. For certain authorized LCS client internal to the PLMN, a subscription profile is unnecessary. These clients are empowered to access any defined service that is not barred for an MS subscriber. This permits positioning of emergency calls without the need for pre-subscription. 5.4.2 System handling component 5.4.2.1 LMU Mobility IVIanagement Function (LIVIIVIF) The LMU Mobility Management Function (LMMF) is responsible for maintaining the operational status of LMUs and registering each LMU in an SMLC. Operation of the LMMF is independent of other logical LCS functions and its output is provided to the PRCF. The LMMF only applies to Type A LMUs. 5.4.2.2 Location System Control Function (LSCF) The Location System Control Function (LSCF) is responsible for coordinating location requests. This function manages call-related and non-call-related positioning requests of GSM LCS and allocates network resources for handling them. The LSCF retrieves MS classmark for the purpose of determining a positioning method. The LSCF performs call setup if required as part of a LCS e.g., putting the ME in a dedicated mode and obtains Cell-ID. It also caters for coordinating resources and activities with regard to requests related to providing assistance data needed for positioning. This function interfaces with the LCCF, LSPF, LSBF and PRCF. Using these interfaces, it conveys positioning requests to the PRCF, relays positioning data to the LCCF and passes charging related data to the LSBF. 5.4.2.3 Location System Billing Function (LSBF) The Location System Billing Function (LSBF) is responsible for charging and billing activity within the network related to location services (LCS). This includes charging and billing of both clients and subscribers. Specifically, it collects charging related data and data for accounting between PLMNs. 5.4.2.4 Location Client Coordinate Transformation Function (LCCTF) The Location Client Coordinate Transformation Function (LCCTF) provides conversion of a location estimate expressed according to a universal latitude and longitude system into an estimate expressed according to a local geographic system understood by the LCF and known as location information. The local system required for a particular LCF will be either known from subscription information or explicitly indicated by the LCF. £75/ (GSM 03.71 version 8.0.0 Release 1999) 17 ETSI TS 101 724 V8.0.0 (2000-10) 5.4.2.5 Location System Operations Function (LSOF) The Location System Operations Function (LSOF) is responsible for provisioning of data, positioning capabilities, data related to clients and subscription (LCS client data and MS data), validation, fault management and performance management of GSM LCS. 5.4.2.6 Location System Broadcast Function (LSBcF) The Location System Broadcast Function (LSBcF) provides broadcast capability. The LSBcF capability is only used when broadcast data is required for E-OTD or A-GPS positioning methods. 5.4.3 Subscriber Component 5.4.3.1 Location Subscriber Authorization Function (LSAF) The Location Subscriber Authorization Function (LSAF) is responsible for authorizing the provision of a location service (LCS) for a particular mobile. Specifically, this function validates that a GSM LCS can be applied to a given subscriber. The LSAF verifies the client MS's subscription. 5.4.3.2 Location Subscriber Privacy Function (LSPF) The Location Subscriber Privacy function is responsible performs all privacy related authorizations. For an target MS it shall authorize the positioning request versus the privacy options of the target MS, if any. 5.4.4 Positioning component 5.4.4.1 Positioning Radio Coordination Function (PRCF) The Positioning Radio Control Function (PRCF) manages the positioning of a mobile through overall coordination and scheduling of resources to perform positioning measurements. This function interfaces with the PSMF and PCF and possibly with a PRAF. The PRCF determines the positioning method to be used based on the QoS, the capabiities of the network, and the MS's location capabilities. It determines which PSMFs to be involved or what to measure, and obtains processed signal measurements from PSMF. Next, it packs the signal measurement data from the PSMF into a certain format and forwards it to the PCF. 5.4.4.2 Positioning Radio Assistance Function (PRAF) The Positioning Radio Assistance Function (PRAF) provides additional support for the PRCF when radio coordination is distributed among multiple network elements. A particular function of the PRAF for network based position methods is to induce positioning signals from the target MS. For mobile based and mobile assisted position methods, the PRAF could induce position signals from the network or from some other external reference source. 5.4.4.3 Positioning Calculation Function (PCF) The Positioning Calculation Function (PCF) is responsible for calculating the position of the mobile. It obtains BTS related data e.g., BTS geographic co-ordinates and stores this data. This function applies an algorithmic computation on the collected signal measurements to compute the final location estimate and accuracy. It also supports conversion of mobile's location estimate between different geodatic reference systems. 5.4.4.4 Positioning Signal Measurement Function (PSMF) The Positioning Signal Measurement Function (PSMF) is responsible for gathering uplink or downlink radio signal measurements for calculation of a mobile's position. These measurements can be positioning related or ancillary. 5.5 Information Flows between Client and Server Other types of national specific information flows may be supported in addition to the information flow specified here. £75/ (GSM 03.71 version 8.0.0 Release 1999) 18 ETSI TS 101 724 V8.0.0 (2000-10) Any of the information flows here indicated may not be externally realized if the information does not flow over an open interface. On the other hand, if a flow goes over an open interface, it shall abide to a well-defmed protocol, which will be further specified in other relevant specifications. 5.5.1 Location Service Request Via the Location Service Request, the LCS client communicates with the LCS server to request for the location information of one or more than one MS within a specified quality of service. There exist two types of location service requests: Location Immediate Request (LIR); and Location Deferred Request (LDR). The following attributes are identified for Location Service Request information flow: - Target MS; - LCS identity; State (idle, dedicated) Event (applicable to LDR requests only); Quality of Service information; Local coordinate system; Geographical area. 5.5.2 Location Service Response The Location Service Response is sent to the LCS client as the result of the Location Service Request by the LCS Server: Immediate Response; and Deferred Response; These deferred responses can be either single or periodic. 5.6 Logical arcliitecture LCS is logically implemented on the GSM structure through the addition of one network node, the Mobile Location Center (MLC). It is necessary to name a number of new interfaces. A generic LCS logical architecture is shown in figure 3. LCS generic architecture can be combined to produce LCS architecture variants. No inference should be drawn about the physical configuration on an interface from figure 3. £75/ (GSM 03.71 version 8.0.0 Release 1999) 19 ETSI TS 101 724 V8.0.0 (2000-10) LMU Type A CBC CBC - SMLC SMLC Urn ± MS BTS (LMU rrype B) Abis BSC Lp Ls HLR MSC/VLR Lh — Lg SMLC Gateway MLC LMU Type B Lc — gsmSCF Figure 3: Generic LCS Logical Architecture 5.6.1 BSS The BSS is involved in the handling of various positioning procedures. Specific BSS functionality is specified in each of the positioning procedures clause. 5.6.2 LCS Client The LCS client is outside the scope of this standard. 5.6.3 GMLC The Gateway Mobile Location Center (GMLC) contains functionality required to support LCS. In one PLMN, there may be more than one GMLC. The GMLC is the first node an external LCS client accesses in a GSM PLMN (i.e. the Le reference point is supported by the GMLC). The GMLC may request routing information from the HLR via the Lh interface. After performing registration authorization, it sends positioning requests to and receives final location estimates from the VMSC via the Lg interface. 5.6.4 SMLC The Serving Mobile Location Center (SMLC) contains functionaUty required to support LCS. In one PLMN, there may be more than one SMLC. The SMLC manages the overall coordination and scheduling of resources required to perform positioning of a mobile. It also calculates the final location estimate and accuracy. Two types of SMLC are possible: NSS based SMLC: supports the Ls interface. BSS based SMLC: supports the Lb interface. £75/ (GSM 03.71 version 8.0.0 Release 1999) 20 ETSI TS 101 724 V8.0.0 (2000-10) An NSS based SMLC supports positioning of a target MS via signaling on the Ls interface to the visited MSC. A BSS based SMLC supports positioning via signaHng on the Lb interface to the BSC serving the target MS. Both types of SMLC may support the Lp interface to enable access to information and resources owned by another SMLC. The SMLC controls a number of LMUs for the purpose of obtaining radio interface measurements to locate or help locate MS subscribers in the area that it serves. The SMLC is administered with the capabilities and types of measurement produced by each of its LMUs. Signaling between an NSS based SMLC and LMU is transferred via the MSC serving the LMU using the Ls interface and either the Um interface for a Type A LMU or the Abis interface for a Type B LMU. Signaling between a BSS based SMLC and LMU is transferred via the BSC that serves or controls the LMU using the Lb interface and either the Um interface for a Type A LMU or the Abis interface for a Type B LMU. The SMLC and GMLC functionality may be combined in the same physical node, combined in existing physical nodes, or reside in different nodes. For Location Services, when a Cell Broadcast Center (CBC) is associated with a BSC, the SMLC may interface to a CBC in order to broadcast assistance data using existing cell broadcast capabilities. The SMLC shall behave as a user. Cell Broadcast Entity, to the CBC (refer to GSM.03.41). 5.6.5 MS The MS may be involved in the various positioning procedures. Specific MS involvement is specified in each of the positioning procedures clause. 5.6.6 LMU An LMU makes radio measurements to support one or more positioning methods. These measurements fall into one of two categories: a) Location measurements specific to one MS used to compute the location of this MS b) Assistance measurements specific to all MSs in a certain geographic area All location and assistance measurements obtained by an LMU are supplied to a particular SMLC associated with the LMU. Instructions concerning the timing, the nature and any periodicity of these measurements are either provided by the SMLC or are pre-administered in the LMU. Two types of LMU are defined: Type A LMU: accessed over the normal GSM air interface. Type B LMU: accessed over the Abis interface. A type A LMU is accessed exclusively over the GSM air interface (Um interface): there is no wired connection to any other network element. A type A LMU has a serving BTS and BSC that provide signaling access to a controlling SMLC. With an NSS based SMLC, a type A LMU also has a serving MSC and VLR and a subscription profile in an HLR. A type A LMU always has a unique IMSI and supports all radio resource and mobility management functions of the GSM air interface that are necessary to support signaling using an SDCCH to the SMLC. A type A LMU supports those connection management functions necessary to support LCS signaling transactions with the SMLC and may support certain call control functions of to support signaling to an SMLC using a circuit switched data connection. NOTE: A network operator may assign specific ranges of IMSI for its LMUs and may assign certain digits within the IMSI to indicate the associated SMLC. Certain digits in the IMSI may also be used as a local identifier for an LMU within an SMLC. To ensure that a Type A LMU and its associated SMLC can always access one another, an LMU may be homed (camped) on a particular cell site or group of cell sites belonging to one BSC or one MSC. For any Type A LMU with a subscription profile in an HLR (applies only with an NSS based SMLC), a special profile is used indicating no supplementary services, except possibly SMS-PP MT (for data download via the SIM application toolkit), and barring of all incoming and possibly outgoing calls. An identifier in the HLR profile also distinguishes an LMU from a normal MS. All other data specific to an LMU is administered in the LMU and in its associated SMLC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 21 ETSI TS 101 724 V8.0.0 (2000-10) A Type B LMU is accessed over the Abis interface from a BSC. The LMU may be either a standalone network element addressed using some pseudo-cell ID or connected to or integrated in a BTS. Signaling to a Type B LMU is by means of messages routed through the controlling BSC for a BSS based SMLC or messages routed through a controlling BSC and MSC for an NSS based SMLC. The following assistance measurements obtained by an LMU have a generic status in being usable by more than one position method: Radio Interface Timing measurements - comprise Absolute Time Differences (ATDs) or Real Time Differences (RTDs) of the signals transmitted by Base Stations, where timing differences are measured relative to either some absolute time difference (ATD) or the signals of another Base Station (RTD). 5.6.7 MSC The MSC contains functionality responsible for MS subscription authorization and managing call-related and non-call related positioning requests of GSM LCS. The MSC is accessible to the GMLC via the Lg interface and the SMLC via the Ls interface. 5.6.8 HLR The HLR contains LCS subscription data and routing information. The HLR is accessible from the GMLC via the Lh interface. For roaming MSs, HLR may be in a different PLMN that the current SMLC. 5.6.9 gsmSCF The Lc interface supports CAMEL access to LCS and is applicable only in CAMEL phase 3. The procedures and signaling associated with it are defined in GSM 03.78 and GSM 09.02, respectively. 5.6.1 LMU and SMLC association The LCS architecture is intended to support a high degree of flexibility, whereby any physical SMLC can support multiple Ls or Lb interfaces (e.g. allowing a BSS based SMLC to serve multiple BSCs) and whereby a mixture of different SMLC types can serve a single network or single MSC area. Figure 4 illustrates the case where different SMLC types and different LMU types are supported in a single MSC area. £75/ (GSM 03.71 version 8.0.0 Release 1999) 22 ETSI TS 101 724 V8.0.0 (2000-10) LMU TypeB PSMF BTS "^-^^^ ^^^^\ BSC-1 LSCF PRAF \ SMLC PRCF PCF LMU TypeB PSMF BTS ^^^^^ \ \ LMU Type A PSMF \ jss^ BTS BSC-2 LSCF PRAF \ \ MSC/VLR LSCF / LMU Type A PSMF JS^ BTS -,„„^^^ / ^~'~~-^..^^ BSC-3 LSCF PRAF ^ LMU TypeB PSMF \ BTS ^^_^^^ / \ / \ / SMLC PRCF PCF Figure 4: lUlixed Network with BSS and NSS based SIVILCs and Type A and B LIUIUs 5.7 Embedded Architecture The embedded common open architecture between the logical LCS functions is shown in figure 5. This architecture appHes to both BSS and NSS based SMLCs and to both types of LMU. The protocol between peer SMLCs allows an LMU to effectively perform measurements for any one or more of several SMLCs and may be used to solve border area problems where LMUs on one side of an SMLC border would not normally be available to the SMLCs that control LMUs on the side. The intent is to impact only the SMLC in resolving border area problems and not LMUs. £75/ (GSM 03.71 version 8.0.0 Release 1999) 23 ETSI TS 101 724 V8.0.0 (2000-10) PSMF (PCF) (Target MS) RRLP (04.31) PSMF (LMU Type A _orB ) LLP (04.71) BSSLAP (08.71) BSSAP-LE (09.31) SMLCPP (08.31) Figure 5: Common Embedded Architecture between Logical LCS Functions 5.8 Assignment of functions to general logical architecture Table 1 : Mapping of LCS Functions into Network Elements MS LMU BTS BSC GMLC SMLC MSC HLR gsmSCF LCS Client LCF X X X X LCCF X LCAF X LMMF X LSCF X LSPF X LSAF X LSBF X X LSBcF X LSOF X X X X X LCCTF X PRAF X PRCF X PCF X X PSMF X X X 6 Signalling Protocols and Interfaces 6.1 Generic Signalling Model for LCS 6.1.1 Protocol layering Figure 6 shows the generic signalling model applicable to LCS for any signalling interaction in which an SMLC forms at least one of the signalling end points. £75/ (GSM 03.71 version 8.0.0 Release 1999) 24 ETSI TS 101 724 V8.0.0 (2000-10) LCS Application Protocol ^ LCS Application Protocol ^ ^ — k \. Relay ^ L3 ^'^ 4 i L3 BSSAP-LE (09.XX) M ► BSSAP-LE ^ ^ L2 Network Layer Network Layer L2 ^ ^ ^ d L1 L1 Physical Layer ' Physical Layer l/F-( 3.g. Un \ ! ^ End Point 1 - MS, LMU, BSC, MSC, SMLC Intermediate ^ Entity( ies) Ls, Lb or Lp End Point 2 - SMLC Figure 6: Generic IVIodel for LCS Signalling to an SMLC The functions performed by each protocol layer are as follows: a) LCS application protocol - this depends on the other signaling end point (e.g. whether a target MS or LMU) and may be absent if supported in the BSSAP-LE layer. The application protocol supports specific LCS functions (e.g. positioning measurements, assistance measurements) and is independent of lower protocol layers. b) BSSAP-LE - this is an extension of BSS AP and carries the LCS application protocol signaling units. Necessary functions include identification of the LCS application protocol and identification, where not provided by the network layer, of the two end points. This layer can be relayed by an intermediate entity or mapped into an equivalent layer 3 protocol used by the other signaling end point. This layer supports segmentation of LCS application layer protocols. c) Network Layer - provides signaling transport between the SMLC and either the other end point or some intermediate entity at which the BSSAP-LE layer is relayed or mapped. The network layer may support connection oriented or connectionless signaling. For second generation circuit oriented applications, the network layer is provided using MTP and SCCP. For third generation and packet oriented applications, other protocols may be used. This layer supports segmentation of LCS application layer protocols. d) Physical Layer - for second generation circuit oriented applications, SS7 signaling links are supported by the physical layer. e) L3 - a protocol layer compatible with or the same as BSSAP-LE. f) L2 - logical link layer for the other endpoint g) LI - physical layer for the other end point. 6.1.2 Message Segmentation Message segmentation is needed to transport any large LCS message that exceeds the message size limitation supported by any GSM interface over which transport is needed. 6.1.2.1 Intermediate Level Segmentation The segmentation of SMLCPP (GSM 08.31) and BSSLAP (GSM 08.71) messages is supported by segmentation mechanisms defined in GSM 08.08, GSM 04.08 and GSM 09.3 L The sending, receiving and all intermediate entities supporting segmentation shall ensure reliable and sequenced delivery of the message segments by appropriate use of the capabilities supported by lower transport and network level protocols. £75/ (GSM 03.71 version 8.0.0 Release 1999) 25 ETSI TS 101 724 V8.0.0 (2000-10) 6.1.2.2 Network Level Segmentation Segmentation and reassembly of large SMLCPP and BSSLAP messages at the network (e.g. SCCP) level may be supported. For message transfer over any interface where network level segmentation is not supported (e.g. Abis interface, Um interface), segmentation at the application level shall be used. This may require support of both network and intermediate level segmentation by certain intermediate entities. 6.2 Signalling between an SMLC, MSC and BSC Figures 7 and 8 show the protocol layers used to support LCS signaling between the SMLC, MSC and BSC with an NSS based and BSS based SMLC, respectively. BSSLAP (08.71) BSSAP SCCP MTP BSC ^ ^ BSSLAP (08.71) ^ p k \. LSCF ^ 4 ^\ Relay/''''^ BSSAP-L[E (09.31) < ► ^ BSSAP BSSAP-LL SCCP SCCP ' <4 ■ SCCP ^ 4 ' ' ► ^ MTP MTP ^ MTP ^ w 1 w MSC SMLC A Ls = highest layer where segmentation of upper layers is supported Figure 7: Signalling Protocols between SMLC, MSC and BSC with NSS based SMLC LSCF BSSAP SCCP MTP MSC BSSLAP SCCP ^ MTP SCCP MTP ^ ^ BSSLAP (08.71) ^ ^ BSSAP-LE (09.31) :^ P ^ ^ SCCP ^ P ^ ^ MTP ^ W BSC A Lb = highest layer where segmentation of upper layers is supported SMLC Figure 8: Signalling Protocols between SMLC, MSC and BSC with BSS based SMLC £75/ (GSM 03.71 version 8.0.0 Release 1999) 26 ETSI TS 101 724 V8.0.0 (2000-10) 6.3 SMLC Signaling to a Target IVIS Figures 9 and 10 show the protocol layers used to support signaling between an SMLC and target MS with an NSS based and BSS based SMLC, respectively. Target MS BSC MSC Um """ A Ls highest layer where segmentation of upper layers is supported SMLC Figure 9: Signalling between an SMLC and Target MS with NSS based SMLC RRLP (04.31) RR (04.08) L2 ( LAPDm) LI Target MS > > Um ^ RRLP (04.31) ^^^ Relay y^ ^ BSSLAP (08.71) \| < BSSLAP ^ ^ RR BSSAP-LE (09.31) BSSAP-LE 4 ► L2 (LAPD) SCCP . SCCP ^ 4 LI MTP < MTP ^ w B£ .C SMLC Ls = highest layer where segmentation of upper layers is supporte Figure 10: Signalling between an SMLC and Target MS with BSS based SMLC 6.4 SIVILC Signalling to a Type A LMU 6.4.1 Signalling using an SDCCH Figures 1 1 and 12 show the protocol layers used to support signaling between an SMLC and a Type A LMU with an NSS and BSS based SMLC, respectively, using an SDCCH on the Um interface. £75/ (GSM 03.71 version 8.0.0 Release 1999) 27 ETSI TS 101 724 V8.0.0 (2000-10) LLP (04.71) DTAP RR L2 ( LAPDm) L1 Type A or B LMU RR L2 (LAPD) L1 BSSAP SCCP MTP BSC DTAP BSSAP SCCP MTP BSSAP-LE-^ SCCP -4 MTP MSC LLP (04.71) BSSAP-LE (09.31) SCCP MTP SMLC Um A Ls Figure 11 : Signalling between an SMLC and a Type A LMU with NSS based SMLC using an SDCCH LLP (04.71; DTAP RR L2 (LAPDm) L1 Type A or B LMU RR L2 (LAPD) LI BSSAR-LE SCCP MTP BSC LLP (04.71] BSSAP-LE (09.31) SCCP MTP SMLC Um Ls Figure 12: Signalling between an SMLC and Type A LMU with BSS based SMLC using an SDCCH 6.4.2 Signalling using a TCH Figures 13 to 15 show the protocol layers that can be used to support signaling between an SMLC and a Type A LMU with an NSS and BSS based SMLC using a TCH on the Um interface. The TCH is assumed to support either transparent or non-transparent synchronous data and may be provided in a multislot configuration. The main usage would be for O&M data and SW download - e.g. during offpeak hours. £75/ (GSM 03.71 version 8.0.0 Release 1999) 28 ETSI TS 101 724 V8.0.0 (2000-10) LLP (04.71) ^ LLP (04.71) ^ DTAP-LE (09.31) DTAP-LE (09.31) ^ ^ L2 (RLP) L2 (RLP) LI M ► ^ ^ ^ w LI (PEG + RA) PEG + RA ^ RA RA < — " — W Type A or B L MU ,,^ BTS TRAU MSG IWF SMLC Figure 13: Signalling between an SMLC and a Type A LMU with NSS based SMLC using a TCH in transparent mode LLP (04.71) M LLP (04.71) w DTAP-LE (09.31) DTAP-LE (09.31) ^ ^ ^ w L2 (RLP) RLP HDLG L2 (HDLG) LI ^ ■< r- LI (PEG + RA PEG + RA 4 RA RA LI -^ ' — ► < — — W Type A or B .Ml' BTS TRAU MSG IWF SMLG Figure 14: Signalling between an SMLC and a Type A LMU with NSS based SMLC using a TCH in non-transparent (NT) mode LLP (04.71) ^ k. LLP (04.71) ^ ^ DTAP-LE (09.31) DTAP-LE (09.31) ^ ^ L2 (RLP) L2 . (RLP) . LI (RA) ^ ^ <— ► LI (FEC H- RA FEC + RA ^ RA l"^ '^ w Type A or B LMI ' j. BTS TRAU m SMLC Figure 15: Signalling between an SMLC and a Type A LMU with BSS based SMLC using a TCH 6.5 SMLC signaling to a Type B LIVIU The protocol layers employed to enable signaling between the SMLC and a type B LMU are shown in figures 16 and 17. £75/ (GSM 03.71 version 8.0.0 Release 1999) 29 ETSI TS 101 724 V8.0.0 (2000-10) LLP (04.71) ■4 — LLP (04.71) — ^ ^\^^ Relay ^^ BSSAP"-''''^ \. Relay y^ 08.58\./^^p 08.58 BSSAP-LI : (09.31) ^ — , , — ^ ^ ^ BSSAP-LP w ^ LAPD SCCP SCCP SCCP LAPD SCCP ■4 — — ^ -4 — — ► w- LI LI MTP MTP MTP MTP ibis -^ — — w- "^"^ ' ► -S Type B LMU BTS with LIV or 1U ^ BSC i MSC L SMLC Figure 16: Signalling between an SMLC and a Type B LMU with NSS based SMLC LLP (04.71) ^ LLP (04.71) .^ ^. \v Relay y^ 08.58 \/^ .4 08.58 BSSAP-LE (09.31) -4 — ► BSSAP-L E^ ^ LAPD SCCP ^^ LAPD SCCP •4 — ^ < — ► LI MTP LI MTP bis "4 — ► _b Type B LMU c BTS with LML r 1 " b; 3C SMLC Figure 17: Signalling between an SMLC and Type B LMU with BSS based SMLC 6.6 SMLC Signalling to a peer SMLC The protocol layers used for SMLC to SMLC signaling are shown in figure 18, where it is assumed that both SMLCs have SS7 link connections to STPs (or there is a direct SS7 link between the SMLCs). In the absence of either a direct link or links to an STP, signaling can go via attached BSCs and MSCs as shown in figure 19 for signaling between BSS based SMLCs sharing the same MSC and in figure 20 for signaling between a BSS based SMLC and an NSS based SMLC associated with different MSCs. £75/ (GSM 03.71 version 8.0.0 Release 1999) 30 ETSI TS 101 724 V8.0.0 (2000-10) SMLCPI (0831) F'<- BSSAP- (0931) LllA- SCCP MTP SMLCP (0831) BSSAP-L (0931) SCCP MTP SMLC STP STP SMLC = highest layer where segmentation of upper layers is supporte Figure 18: SIUILC to SIVILC Signalling via SS7 STPs SMLCPI = (0831) SMLCPP (0831) ^i • . w ! \. Fielay^ \. Ftelay^^ ^^ Ftelay ^^ RSSAP-LE (0931) ^SSAP-LE (0931) -► < — N bSSAP- d BSSAF ■■* * BSSAFJ - BSSA^ BSSAP BSSAP-LE SCCP SCCP SCCP SCCP SCCP SCCP SCCP ^ — ^ SCCP < — ► 4 ^ MTP MTP MTP MTP MTP MTP MTP MTP < \ ► SIVLC Lb BSC A MSC A BSC Lb SIVLC = highest layer where segmentation of upper layers is supported Figure 19: SMLC to SMLC Signalling via associated BSCs and MSC (BSS based SMLCs) SIVLCPP (0831) BSSAP-LE (0931) SCCP MTP SIVLC BSC MSC MSC Lb A E Ls = highest layer where segmentation of upper layers is supported SIVLC Figure 20: SMLC to SMLC Signalling via BSC and MSCs (BSS to NSS based SMLC) £75/ (GSM 03.71 version 8.0.0 Release 1999) 31 ETSI TS 101 724 V8.0.0 (2000-10) 7 General Network Location Procedures 7.1 State Description for the GIVILC 7.1.1 GMLC States 7.1.1.1 NULL State In the NULL state, a particular location request from some LCS client either has not been received yet or has already been completed. After a location request is received from a LCS client, the GMLC remains in the NULL state while the identity of the client and nature of its location request are verified. . While the NULL state exists conceptually, it need not be represented explicitly in the GMLC. 7.1 .1 .2 INTERROGATION State In this state, the GMLC has sent an interrogation to the home HLR of the MS to be located and is awaiting a response giving the VMSC address and IMSI for this MS. 7.1.1.3 LOCATION State In this state, the GMLC has sent a location request to the VMSC serving the MS to be located and is awaiting a response containing a location estimate. 7.1.2 State Functionality 7.1.2.1 State Transitions Location Request - Interrogate HLR for VMSC address or Timeout or Error Receive VMSC address from HLR Location Request - GMLC knows VMSC address Figure 21 : State Transitions in thie GIVILC Moving from NULL to INTERROGATION state: If the GMLC does not know the VMSC address or MS IMSI when it receives a location service request from some LCS client, it moves from the NULL state to the INTERROGATION state and sends a request to the MS's home HLR for the VMSC address and IMSI. £75/ (GSM 03.71 version 8.0.0 Release 1999) 32 ETSI TS 101 724 V8.0.0 (2000-10) Moving from NULL to LOCATION state: If the GMLC already knows both the VMSC address and MS IMSI when it receives a location service request from some LCS client (e.g. from information retained for an earlier location request for the same MS), it moves from the NULL state to the LOCATION state and sends a location request to the VMSC. Moving from INTERROGATION to LOCATION state: After the GMLC, in the INTERROGATION state, receives the VMSC address and IMSI from the home HLR, it enters the LOCATION state and sends a location request to the VMSC of the MS being located. Moving from LOCATION to NULL state: After the GMLC receives a location estimate response from the VMSC, it forwards the location estimate to the requesting LCS client and reenters the NULL state. 7.1 .2.2 INTERROGATION Timer Function The GMLC runs a timer while in the INTERROGATION state to limit the amount of time waiting for an interrogation response from the HLR. If the timer expires before an interrogation response is received, the GMLC indicates a location failure to the LCS client and reenters the NULL state. 7.1 .2.3 LOCATION Timer Function The GMLC runs a timer while in the LOCATION state to limit the amount of time waiting for a location estimate response from the VMSC. If the timer expires before a response is received, the GMLC indicates a location failure to the LCS client and reenters the NULL state. 7.2 State Description for the VIVISC 7.2.1 VIVISC States 7.2.1.1 IDLE state In this state, the VMSC location service is inactive for a particular MS. The MS may be known in the VLR (except for a SIMless Emergency call or where the MS record has been canceled or lost in the VLR), but there may not be an active Mobility Management or Radio Resource connection to the MS. 7.2.1.2 LOCATION State In this state, the VMSC is awaiting a response from either an NSS based SMLC or BSC after requesting the location for a particular MS. In this state, a Radio Resource connection and a Mobility Management connection to the target MS will be active - allowing the SMLC and MS to exchange positioning related messages for mobile based and mobile assisted position methods. For certain position methods (e.g. network based position methods), the SMLC may invoke substates in the VMSC during which other types of association are maintained with the MS (e.g. temporary call establishment). Such substates are defined in later clauses for each positioning method. In this state, the VMSC may also transfer positioning related messages between an NSS based SMLC and the target MS and/or between an NSS based SMLC and certain LMUs served by the VMSC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 7.2.2 State Functionality 7.2.2.1 State Transitions 33 ETSI TS 101 724 V8.0.0 (2000-10) Request Location from the SMLC orBSC Receive Location results from tine SIVILCor BSC or Timeout Transfer Positioning IVIessages Figure 22: State Transitions in the VIUISC Moving from IDLE to LOCATION state: After a request has been received to locate a particular MS and the MS subscription options have been verified, a location request is sent to the SMLC or BSC associated with the serving cell of the MS to be located: the VMSC then enters the LOCATION state. Before entering this state, the VMSC must have obtained the current cell ID for the MS and setup a Radio Resource and Mobility Management connection to the MS if none was previously active. Moving from LOCATION to IDLE state: After the return of a location estimate result from the SMLC, the VMSC shall reenter IDLE state. 7.2.2.2 LOCATION Timer Function The VMSC runs a timer while in the LOCATION state to limit the amount of time waiting for a location response from the SMLC or BSC. If the timer expires before such information is received, the VMSC indicates a location failure to the original requesting entity and reenters IDLE state. 7.3 State Description for the BSC 7.3.1 BSC States 7.3.1.1 IDLE State In this state, the BSC location service is inactive for a particular MS. £75/ (GSM 03.71 version 8.0.0 Release 1999) 34 ETSI TS 101 724 V8.0.0 (2000-10) 7.3.1.2 LOCATION State In this state, the BSC is awaiting a response from a BSS based SMLC or the VMSC after requesting the location for a particular MS. In this state, a Radio Resource connection to the target MS will be active - allowing the SMLC and MS to exchange positioning related messages for mobile based and mobile assisted position methods. For certain position methods (e.g. network based position methods), the SMLC may invoke substates in the BSC during which other types of association or procedure are supported with the MS (e.g. temporary call establishment, handover). Such substates are defined in later clauses for each positioning method. In this state, the BSC may transfer positioning related messages between the SMLC and the target MS and/or between the SMLC and certain LMUs served by the BSC. 7.3.2 State Functionality 7.3.2.1 State Transitions Request / \ Receive Location from\ / i Location results tiie SIVILC or ^^ /\ from the SIVILC VIVISC \ / orVIVISCor Timeout Transfer Positioning IVIessages Figure 23: State Transitions in the BSC Moving from IDLE to LOCATION state: After a request has been received (e.g. from the VMSC or from a client internal to the BSC) to locate a particular MS served by the BSC, a location request is sent to either the BSS based SMLC associated with the serving cell or to the VMSC (with an NSS based SMLC): the BSC then enters the LOCATION state. Before entering this state, a Radio Resource connection to the MS must have been already established by the VMSC. Moving from LOCATION to IDLE state: After the return of a location estimate result from the SMLC or VMSC, the BSC shall reenter IDLE state. 7.3.2.2 LOCATION Timer Function The BSC runs a timer while in the LOCATION state to limit the amount of time waiting for a location response from the SMLC or VMSC. If the timer expires before such information is received, the BSC indicates a location failure to the original requesting entity and reenters IDLE state. £75/ (GSM 03.71 version 8.0.0 Release 1999) 35 ETSI TS 101 724 V8.0.0 (2000-10) 7.4 State Description for the SIVILC 7.4.1 SIVILC States 7.4.1.1 NULL state This is a conceptual rather than actual state in which a certain location request from a particular VMSC or BSC either has not yet been received or has been completed. 7.4.1.2 LOCATION State This state exists after the SMLC has received a location request from a VMSC or BSC and persists while the SMLC is obtaining position measurements fr)r a particular positioning method until such time as positioning measurements have been received and a location estimate has been computed and returned to the VMSC or BSC. When sufficient positioning measurement results have been received, the SMLC either evaluates them, if they include an already computed location estimate, or uses them to compute a location estimate. The SMLC then has the option of either reinitiating another positioning attempt, if the location estimate did not satisfy the required QoS, or returning the location estimate to the VMSC or BSC. 7.4.2 State Functionality 7.4.2.1 State Transitions Location , „ Request \ / i , f^^^urn from a Y /\ TTI VMSC or ' ^ ^ results to the BSC VMSC or BSC or Timeout Initiate Positioning via tine VMSC or BSC Figure 24: State Transitions in the SIVILC Moving from NULL to LOCATION state: After a location request is received from the VMSC or BSC, the SMLC chooses a positioning method and initiates the appropriate position measurements. It then enters the LOCATION state. £75/ (GSM 03.71 version 8.0.0 Release 1999) 36 ETSI TS 101 724 V8.0.0 (2000-10) Moving from LOCATION to NULL state: When the SMLC has obtained a location estimate that best meets the requested QoS parameters, it returns this to the VMSC or BSC and reenters the NULL state. 7.4.2.2 LOCATION Timer Function The SMLC runs a timer while in the LOCATION state to limit the total amount of time that positioning can be active. This timer should be related to any response time indicated in the location request QoS parameters. If the timer expires before a final location estimate has been produced, the SMLC either returns the best existing location estimate to the VMSC (e.g. an estimate based on the current cell ID) or returns a failure indication. It then reenters the NULL state. 7.5 Usage of SCCP Connections on the Ls and Lb interfaces SCCP connection oriented signaling between an SMLC and MSC (NSS based SMLC) or SMLC and BSC (ESS based SMLC) is used to support SMLC signaling to a type A LMU, serving BSC, serving MSC or target MS. Two distinct types of SCCP connection are needed. 7.5.1 SCCP connection for positioning of a target MS The MSC and BSC set up this connection when they request a location estimate for a target MS. The MSC/BSC sends the BSSMAP-LE Perform Location Request to the SMLC inside an SCCP Connection Request message. Signaling between the SMLC and target MS is then relayed by the serving MSC or BSC between this SCCP connection and the main signaling link to the MS. The same SCCP connection is also used to transfer BSSLAP messages between the SMLC and serving BSC. See figures 25 and 26. Target ^ ^ DOr* MSC MS SDDCH or U<3\J SCCP SCCP oMi-u i k FACCH i L 1 Connection BSSAP A A Connection BSSAP-LE (09.31) ft'' BSSLAP (08.71) RRLP (04.31) Figure 25: SCCP based signalling for MS positioning with an NSS based SMLC Target I 30r* ^ k. OKA 1 r> MS SDDCH or •4 w SCCP oMi-o i k FACCH i BS Connection SAP-LE (09.31) 1^ L> k BSSLAP (08.71) RRLP (04.31) Figure 26: SCCP based signalling for MS positioning with a BSS based SMLC £75/ (GSM 03.71 version 8.0.0 Release 1999) 37 ETSI TS 101 724 V8.0.0 (2000-10) 7.5.2 SCCP connection to access a type A LMU The MSC, BSC or SMLC setup this connection to enable LCS messages to be transferred to or from a type A LMU. The MSC, BSC or SMLC sends a BSSMAP-LE LMU Connection Request message inside an SCCP Connection Request message. SignaHng is subsequently relayed through the serving MSC and BSC using this SCCP connection as shown in figures 27 and 28. Type A LMU BSC ^ ^ MSC -M k. ORJII r* SDDCH or FACCH SCCP SCCP oMLU i V 1 Connection BSSAP A A Connection BSSAP-LE (09.31) ▲ A LLP (04.71) Figure 27: SCCP based signalling to access a type A LMU with an NSS based SMLC Type A BSC ^ ^ OHill ^s or B LMU SDDCH or ■^ ► SCCP SMLu i k FACCH . Connection BSSAP-LE (09.31) ▲ '^ LLP (04.71) Figure 28: SCCP based signalling to access a type A LMU with a ESS based SMLC 7.6 General Network Positioning Procedures The generic network positioning procedure of providing the location information of an MS subscriber can be partitioned into the following procedures: Location Preparation Procedure This generic procedure is concerned with verifying the privacy restrictions of the MS subscriber, reserving network resources, communicating with the MS to be located and determining the positioning method to be used for locating the MS subscriber based on the requested QoS and the MS and network capabilities. Positioning Measurement Establishment Procedure This procedure is concerned with performing measurements by involving the necessary network and/or MS resources. Depending on the positioning method to be used for locating the MS the internals of this procedure can be positioning method dependent. The procedure is completed with the end of the positioning measurements. Location Calculation and Release Procedure This generic procedure is initiated after the measurements are completed and is concerned with calculating the location of the MS and releasing all network and/or MS resources involved in the positioning. £75/ (GSM 03.71 version 8.0.0 Release 1999) 38 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.1 Mobile Terminating Location Request (MT-LR) Figure 29 illustrates general network positioning for LCS clients external to the PLMN. In this scenario, it is assumed that the target MS is identified using either an MSISDN or IMSI. Client GMLC 1 . LCS Service ReqL HLR . MAP Send Routing Info MAP Send Routing Info f[)r LCS ^'^'^■ 4. MAP Provide Subscriber Location VMSC or LCS SMLC 5. MS I 'aging, Authenticatiot , Ciphering BSC 6. DTAP LC! 1 Location Notificatior Invoke 7. DTAP LCS I ocation Notification F 8. BSSMAP-LE P( rform Location requept 9. BSSMAP Per c orm Location requesi 10. BSSMAP-LE Per brm Location request MS eturn Result 1 1 . Messages for individual positioning methods ' 16. LCS Service R 15. MAP Provide Sulpscriber Location apk. :sponse 12. BpSMAP-LE Perform Lc cation response 13. BSSI /lAP- LE Perform Lo :ation response 14. BSSMAP Psrform Location respdnse Figure 29: General Network Positioning for a IVIT-LR 7.6.1.1 Location Preparation Procedure 1) An external LCS client requests the current location of a target MS from a GMLC. The GMLC verifies the identity of the LCS client and its subscription to the LCS service requested and derives the MSISDN or IMSI of the target MS to be located and the LCS QoS from either subscription data or data supplied by the LCS client. For a call related location request, the GMLC obtains and authenticates the called party number of the LCS client (refer to Annex A for further details)^ If location is required for more than one MS, or if periodic location is requested, steps 2 to 12 below may be repeated. 2) If the GMLC already knows both the VMSC location and IMSI for the particular MSISDN (e.g. from a previous location request), this step and step 3 may be skipped. Otherwise, the GMLC sends a MAP_SEND_ROUTING_INFO_FOR_LCS message to the home HLR of the target MS to be located with either the IMSI or MSISDN of this MS. £75/ (GSM 03.71 version 8.0.0 Release 1999) 39 ETSI TS 101 724 V8.0.0 (2000-10) 3) The HLR verifies that the SCCP calling party address of the GMLC, corresponds to a known GSM network element that is authorized to request MS location information. The HLR then returns the current VMSC address and whichever of the IMSI and MSISDN was not provided in step 2 for the particular MS. 4) The GMLC sends a MAP_PROVIDE_SUBSCRIBER_LOCATION message to the VMSC indicated by the HLR. This message carries the type of location information requested (e.g. current location), the MS subscriber's IMSI, LCS QoS information (e.g. accuracy, response time) and an indication of whether the LCS client has the override capability. For a call related location request, the message also carries the LCS client's called party number. For a value added LCS client, the message shall carry the client name if available and, for a call unrelated location request, the identity of the LCS client. In other cases, inclusion of the client name and/or identity is optional. 5) If the GMLC is located in another PLMN or another country, the VMSC first authenticates that a location request is allowed from this PLMN or from this country. If not, an error response is returned. If the target MS has an established circuit call other than speech, the location request may be denied and an error response is then returned to the GMLC. If the location request is allowed for a non-speech circuit call, it shall be up to the SMLC to decide, on the basis of the applicable position methods and requested QoS, whether positioning is possible. The VMSC then verifies LCS barring restrictions in the MS user's subscription profile in the VLR. In verifying the barring restrictions, barring of the whole location request is assumed if any part of it is barred or any requisite condition is not satisfied. If LCS is to be barred without notifying the target MS and a LCS client accessing a GMLC in the same country does not have the override capability, an error response is returned to the GMLC. Otherwise, if the MS is in idle mode, the VLR performs paging, authentication and ciphering. This procedure will provide the MS user's current cell ID and certain location information that includes the TA value in the BSSMAP Complete layer 3 Information used to convey the Paging Response. If the target MS supports any MS based or MS assisted positioning method(s), the MS will also provide the BSC and MSC with the positioning method(s) it supports via controlled early classmark sending (see GSM 04.08 and 08.08). If the MS is instead in dedicated mode, the VMSC will already have any early classmark information and will have been supplied with the current cell ID from either the serving BSC or serving MSC in the case of an established call with MSC-MSC handover. 6) If the location request comes from a value added LCS client and the MS subscription profile indicates that the MS must either be notified or notified with privacy verification and the MS supports notification of LCS (according to the MS Classmark 2), a DTAP LCS Location Notification Invoke message is sent to the target MS indicating the type of location request (e.g. current location), the identity of the LCS client and whether privacy verification is required. For a call related location request, the LCS client identity shall be set to the LCS client's called party number if no separate LCS client identity was received from the GMLC. Optionally, the VMSC may after sending the DTAP LCS Location Notification Invoke message continue in parallel the location process, i.e. continue to step 8 without waiting for a DTAP LCS Location Notification Return Result message in step 7. 7) The target MS notifies the MS user of the location request and, if privacy verification was requested, the target MS indicates to the MS user whether the location request will be allowed or not allowed in the absence of a response and waits for the user to grant or withhold permission. The MS then returns a DTAP LCS Location Notification Return Result to the VMSC indicating, if privacy verification was requested, whether permission is granted or denied. Optionally, the DTAP LCS Location Notification Return Result message can be returned some time after step 6, but before step 15. If the MS user does not respond after a predetermined time period, the VMSC shall infer a "no response" condition. The VMSC shall return an error response to the GMLC if privacy verification was requested and either the MS user denies permission or there is no response with the MS subscription profile indicating barring of the location request in the absence of a response. 8) The VMSC sends a MAP_PERFORM_LOCATION message to the SMLC associated with the MS's current cell location. The BSSMAP-LE message includes the type of location information requested, the MS's location capabilities and currently assigned radio channel type (SDCCH, TCH-FR or TCH-HR), the requested QoS and the current Cell ID and, if available, any location information including the TA value received in step 5. 9) If the SMLC is BSS based, the VMSC instead sends the BSSMAP PERFORM LOCATION message to the serving BSC for the target MS. 10) hi the case of a BSS based SMLC, the BSC forwards the BSSMAP-LE PERFORM LOCATION request received in step 9 to the SMLC. The BSC may add additional measurement data to the message to assist with positioning. The message is transported inside an SCCP connection request. £75/ (GSM 03.71 version 8.0.0 Release 1999) 40 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.1 .2 Positioning Measurement Establishment Procedure 1 l)If the requested location information and the location accuracy within the QoS can be satisfied by the reported cell ID and, if available, TA value, the SMLC may send a MAP_PERFORM_LOCATION ack. immediately. Otherwise, the SMLC determines the positioning method and instigates the particular message sequence for this method defined in subsequent clauses. If the position method returns position measurements, the SMLC uses them to compute a location estimate. If there has been a failure to obtain position measurements, the SMLC may use the current cell ID and, if available, TA value to derive an approximate location estimate. If an already computed location estimate is returned for an MS based position method, the SMLC may verify consistency with the current cell ID and, if available, TA value. If the location estimate so obtained does not satisfy the requested accuracy or the location attempt failed, e.g. due to missing data,and sufficient response time still remains, the SMLC may instigate a further location attempt using the same (e.g. providing more assistance data to MS) or a different position method. If a vertical location coordinate is requested but the SMLC can only obtain horizontal coordinates, these may be returned. 7.6.1 .3 Location Calculation and Release Procedure 12) When location information best satisfying the requested location type and QoS has been obtained, the SMLC returns it to the VMSC in a Perform Location response if the SMLC is NSS based. If a location estimate could not be obtained, the SMLC returns a Perform Location response containing a failure cause and no location estimate. 13)For a BSS based SMLC, the location information is instead returned to the serving BSC. 14) In the case of a BSS based SMLC, the BSC forwards the BSSMAP PERFORM LOCATION response received instep 13 to the VMSC. 15)The VMSC returns the location information and its age to the GMLC, if the VMSC has not initiated the Privacy Verification process in step 6. If step 6 has been performed for privacy verification, the VMSC returns the location information only, if it has received a DTAP LCS Location Notification Return Result indicating that permission is granted. If a DTAP LCS Location Notification Return Result message indicating that permission is not granted is received, or there is no response with the MS subscription profile indicating barring of location in the absence of a response, the VMSC shall return an error response to the GMLC. If the SMLC did not return a successful location estimate, but the privacy checks in steps 5-7 were successfully executed, the VMSC may return the last known location of the target MS if this is known and the LCS client is requesting the current or last known location. The VLR may then release the Mobility Management connection to the MS, if the MS was previously idle, and the VMSC may record billing information. 16) The GMLC returns the MS location information to the requesting LCS client. If the LCS client requires it, the GMLC may first transform the universal location coordinates provided by the VMSC into some local geographic system. The GMLC may record billing for both the LCS client and inter-network revenue charges from the VMSC's network. 7.6.2 MT-LR without HLR Query - applicable to North America Emergency Calls only Figure 30 illustrates location for a North American Emergency Services call, where an emergency services client identifies the target MS using an IMSI, MSISDN or NA-ESRK plus, possibly IMEI, that were previously provided to it by the VMSC (e.g. see clause?. 6.4). The emergency services client also identifies the VMSC to the GMLC by providing an NA-ESRD or NA-ESRK or by referring to information for the target MS already stored in the GMLC. This allows the GMLC to request location from the VMSC without first querying the home HLR of the target MS. This is necessary when the home HLR either cannot be identified (e.g. client provides an NA-ESRK but not IMSI or MSISDN) or does not support the LCS query procedure. £75/ (GSM 03.71 version 8.0.0 Release 1999) 41 ETSI TS 101 724 V8.0.0 (2000-10) Client GMLC HLR VMSC SMLC BSC MS 1. LCS Service Ffequiist 2. MAP Provide Su jscriber Locatioi 3. BSS VIAP-LE Perform Location Request 4. Messages for individual positioning methods 7. LCS Service Respc 6. MAP Provide Subscriber Location acl<. 5. BSS VIAP-LE Perform Location Response Figure 30: Positioning for a Emergency Services lUIT-LR without HLR Query 1) Same as step 1 in figure 29 but with the LCS client identifying first the target MS by an IMSI, MSISDN or NA- ESRK and possibly IMEI and, second, the VMSC by an NA-ESRK or NA-ESRD. 2) If the GMLC already has stored information for the target MS (e.g. from a prior location estimate delivery to the LCS client), the GMLC may determine the VMSC from this information. Otherwise, the GMLC determines the VMSC using the NA-ESRK or NA-ESRD - with use of the NA-ESRK taking priority over that of the NA- ESRD. The MAP_PROVIDE_SUBSCRIBER_LOCATION message sent to the VMSC carries the IMSI, MSISDN or NA-ESRK and, if provided, the IMEI for the target MS, as well as the required QoS and an indication of a location request from an emergency services client. The VMSC identifies the target MS using the IMSI, MSISDN or NA-ESRK and, if provided, the IMEI. 3) The VMSC verifies that MS privacy is overridden by the emergency services provider and that positioning is not prevented for other reasons (e.g. unreachable MS, inapplicable call type to the MS). The VMSC then sends a BSSMAP-LE Perform Location Request to the SMLC, either directly or via the BSC, as in steps 8-10 for a normal MT-LR. 4) The SMLC performs positioning as in step 11 for a normal MT-LR. 5) The SMLC returns a location estimate to the VMSC either directly or via the BSC as in steps 12-14 for a normal MT-LR. 6) to (7) Same as steps 15 to 16 for a normal MT-LR. 7.6.3 MT-LR for a previously obtainecJ location estimate Every time the location estimate of a target MS subscriber is returned by the SMLC to the VMSC, the VMSC may store the location estimate together with a time stamp in the subscriber's VLR record. The time stamp is the time at which the location estimate is stored at the VLR i.e. after the SMLC returns the location estimate to the VMSC. The time stamp indicates the 'age' of the location estimate. 7.6.3.1 Initial Location In the context of an originating emergency call the location estimate and the associated time stamp at the commencement of the call set-up is referred to as 'initial location '. ETSI (GSM 03.71 version 8.0.0 Release 1999) 42 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.3.2 Current Location After a location attempt has succesfully delivered a location estimate and its assocoiated time stamp, the location estimate and time stamp is referred to as the 'current location' at that point in time. 7.6.3.3 Last known Location The current location estimate and its associated time stamp are stored in MSCA'LR and until replaced by a later location estimate and a new time stamp is referred to as the 'last known location '. The last known location may be distinct from the initial location - i.e. more recent. 7.6.3.4 Security and Privacy The handling of security and privacy of the target MS with regard to returning the last known or initial location estimate of the target MS shall be the same as when the target MS is reachable for positioning, (i.e. the requesting LCS client is authorized and the privacy of the target MS is secured before the VMSC check the VLR status of the target MS (i.e. whether the MS is marked as attached or detached in the VLR). 7.6.3.5 Failing to locate the target IVIS In case of a 'Detached' or 'Not Reachable' target MS, the last known location and a time stamp stored at the VLR, may be returned to a LCS client requesting location information if the LCS client specifically requested the current or last known location. This does not apply to a value added LCS client where the target MS subscribes to notification of the location request: if the notification cannot be performed, the VMSC shall reject the location request. NOTE: Due to CAMEL, the MSCA'LR may already be storing other location information parameters like location number, cell id, location area identity and VLR number in the subscriber's VLR record. When a request for location information is received at the VMSC, the request shall indicate whether the 'last known location of the target MS' should be returned in case of a 'detached' or 'not reachable' target MS. If the VLR has a valid copy of the subscriber's permanent data and the target MS's privacy settings are such that positioning is allowed, then the following cases can occur. 7.6.3.5.1 Target MS is 'Not Reachable' If the target MS is marked as 'attached' in the VLR, the VMSC orders paging of the target MS. If paging fails, due to target MS being 'not reachable' then VMSC shall check whether the LCS client has requested 'last known location' in case of 'not reachable' target MS. If such a request exists and notification to the target MS does not apply for a value added LCS client, the VMSC shall include the last known location together with the time stamp available in its response to the request for location information. An indicator of 'last known location' returned shall be marked at the CDR at VMSC. 7.6.3.5.2 Target MS is 'Detached' If the target MS is marked as 'detached' in the VLR, the VMSC shall check whether the LCS client has requested 'last known location' in case of 'detached' target MS. If such a request exists and notification to the target MS does not apply for a value added LCS client, the VMSC includes the 'last known location' together with the time stamp available in its response to the request for location information. An indicator of 'last known location' returned shall be marked at the CDR at VMSC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 43 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.3.5.3 Target MS is Reachable but Positioning Fails If the target MS is reachable (e.g. paging succeeds), but the VMSC is unable to obtain a current location estimate, the VMSC shall check whether the LCS client has requested 'last known location'. If such a request exists and notification to the target MS either does not apply or was successfully executed for a value added LCS client, the VMSC includes the 'last known location' together with the time stamp available in its response to the request for location information. An indicator of 'last known location' returned shall be marked at the CDR at VMSC. 7.6.3.5.4 Target MS is 'Purged' If the target MS is marked as 'Purged' in HLR, then an indication 'Absent Subscriber' is returned to the GMLC. 7.6.4 Network Induced Location Request (NI-LR) Figure 3 1 illustrates positioning for an emergency service call. LCS Client GMLC HLR VMSC SMLC 2. BSSMAP Complete _3 (CM Service F equest) 3. Emergency Call Origination 4. BSS MAP-LE Perfbrr i Location Reque st BSC MS CM Service Re( |uest 5. Messages for individual positioning methods 9. Location Informatiop < 7. MAP Subscrib sr Location Report 8. MAP Subscriber L ocation Report ack 11. MAPSubscril: 12. MAP Subscriber er Location Report Location Report acl 6. BSS MAP-LE Perform Location Response 10. Emergency Call Release Figure 31 : Positioning for a NI-LR Emergency Service Call £75/ (GSM 03.71 version 8.0.0 Release 1999) 44 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.4.1 Location Preparation Procedure 1) An initially idle MS requests an SDCCH and sends a DTAP CM Service Request indicating a request for an Emergency Service call to the VMSC via the BSC. 2) The BSC includes the current cell ID and may include certain other location information (e.g. the TA value) within the BSSMAP Complete Layer 3 Information message used to convey the CM service request across the A-interface. The MS may identify itself using a TMSI, IMSI or IMEI. 3) The VMSC, BSC and MS continue the normal procedure for emergency call origination towards the appropriate emergency services client. Depending on local regulatory requirements, the sending of call setup information into the PSTN may be delayed until either the MS's location has been obtained or the location attempt has failed or a PLMN defined timer has expired before location was obtained. Call setup information sent into the PSTN may include the MS location (if already obtained) plus information that will enable the emergency service provider to request MS location at a later time (e.g. NA-ESRD and NA-ESRK in North America). 4) At any time after step 1 and after sufficient time has been allowed to enable completion of early classmark sending to the BSC and MSC where the MS supports any MS assisted or MS based positioning method(s), the VMSC may initiate procedures to obtain the MS's location. These procedures may run either in parallel with the emergency call origination or while emergency call origination is suspended to delay sending of call setup information into the PSTN according to step 3. The VMSC sends a BSSMAP-LE :Perform Location Request message to the SMLC associated with the MS's current location area - either directly or via the serving BSC (see steps 8-10 for an MT-LR). This message includes the MS's location capabilities and currently assigned radio channel type (SDCCH, TCH-FR or TCH-HR), the QoS required for an emergency call and the current Cell ID and any location information including the TA value received in step 2. 7.6.4.2 Positioning Measurement Establishment Procedure 5) The actions described under step 1 1 for a MT-LR are performed. If a speech compatible traffic channel is required for network based positioning (e.g. TO A), the same traffic channel may be used for both the positioning and the emergency call. In that case, the traffic channel may be allocated by either the positioning procedure or emergency call origination procedure. 7.6.4.3 Location Calculation and Release Procedure 6) When a location estimate best satisfying the requested QoS has been obtained, the SMLC returns it to the VMSC - either directly or via the serving BSC (see steps 12-14 for an MT-LR). 7) Depending on local regulatory requirements, the VMSC may send a MAP Subscriber Location report to a GMLC associated with the emergency services provider to which the emergency call has been or will be sent. This message shall carry any location estimate returned in step 6, the age of this estimate and may carry the MSISDN, IMSI and IMEI of the calling MS. In North America, any NA-ESRD and any NA-ESRK that may have been assigned by the VMSC shall be included. The message shall also indicate the event that triggered the location report. If location failed (i.e. an error result was returned by the SMLC in step 8), an indication of failure rather than a location estimate may be sent to the GMLC: the indication of failure is conveyed by not including a location estimate in the MAP Subscriber Location Report. 8) The GMLC acknowledges receipt of the location information. For a North American Emergency Services call, the GMLC shall store the location information for later retrieval by the emergency services LCS client. 9) The GMLC may optionally forward the information received in step 7 to the emergency services LCS client. For a North American emergency services call the client is expected to obtain the location information by requesting it from the GMLC 10) At some later time, the emergency services call is released. 1 l)For a North American Emergency Services call, the MSC sends another MAP Subscriber Location Report to the GMLC. This message may include the same parameters as before except that there is no position estimate and an indication of emergency call termination is included. 12) The GMLC acknowledges the MSC notification and may then release all information previously stored for the emergency call. £75/ (GSM 03.71 version 8.0.0 Release 1999) 45 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.5 Network ln(duce(d Location Request (NI-LR) from a Serving BSC for a target MS in dedicated mode Figure 32 illustrates how a serving BSC may obtain the location of a target MS that is already in dedicated mode on behalf of some PLMN operator LCS client - e.g. to support handover. The procedure is valid for an NSS based SMLC in all circumstances and for a BSS based SMLC when local regulatory requirements do not require privacy checking for PLMN operator initiated location. LCS Client VMSC SMLC 1 . LCS Service Request 3. BSSMAP Peform Location request 4. BSSIVIAP-LE Perform Locajion request BSC BSSIVIAP-LE Perform Locatic MS n request 5. Messages for individual positioning methods 7. 3SSMAP-LE Perform Location rssponse 9. LCS Service Response BSSMAP-LE Perform Locatiot response 8. BSSMAP Pert irm Location response 7.6.5.1 Figure 32: Network Induced Location Request from a Serving BSC Location Preparation Procedure 1) An LCS client within the BSC or within the PLMN requests the current location of a target MS from the serving BSC 2) The BSC sends a BSSMAP-LE PERFORM LOCATION request message to the SMLC if this is BSS based. The BSSMAP-LE message includes the MS's location capabilities and currently assigned radio channel type (SDCCH, TCH-FR or TCH-HR), the requested QoS and the current Cell ID. The message may also contain additional measurements available to the BSC (e.g. TA value). 3) If the SMLC is NSS based, the BSC instead sends the BSSMAP Perform Location Request to its serving MSC with the type of PLMN operator LCS client. 4) In the case of an NSS based SMLC, the MSC verifies in the subscription profile of the target MS that the MS permits location by the indicated type of LCS client. The MSC then forwards the BSSMAP-LE PERFORM LOCATION request received in step 3 to the SMLC. 7.6.5.2 Positioning Measurement Establishment Procedure 5) Refer to step 1 1 for an MT-LR. £75/ (GSM 03.71 version 8.0.0 Release 1999) 46 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.5.3 Location Calculation and Release Procedure 6) When a location estimate best satisfying the requested QoS has been obtained, the SMLC returns it to the BSC if the SMLC is BSS based. 7) If the SMLC is NSS based, the BSC instead returns the location estimate to the MSC. 8) In the case of a NSS based SMLC, the MSC forwards the BSSMAP PERFORM LOCATION response received in step 7 to the BSC. 9) The BSC returns the MS location estimate to the requesting LCS client. 7.6.6 Mobile Originating Location Request (MO-LR) The following procedure allows an MS to request either its own location, location assistance data or broadcast assistance data message ciphering keys from the network. Location assistance data may be used subsequently by the MS to compute its own location throughout an extended interval using a mobile based position method. The ciphering key enables the MS to decipher other location assistance data broadcast periodically by the network. The MO-LR after location update request may be used to request ciphering keys or GPS assistance data using the follow-on procedure described in GSM 04.08. The procedure may also be used to enable an MS to request that its own location be sent to another LCS client. LCS Client GMLC 12. 14. Location Infornation VMSC SMLC ?. BSSMAP Complete La^ er 3 (CM Service 3. Authentication, Ciph 4. DTAPLCSIVIO-.R Invoice ► 3SSMAP-LE Perform Locatic|n Request 6. BSSMAP Perform Loca:ion Request BSC Cm Service ReqLJest Request) iring or DTAP CIV Service Accept 7. BSSM^P-LE Perform Loiation Request MS W: 8. Messages for individual positioning methods or transfer qf location assistance data 9.B$SmAP-LE Perform Locationl Response. 10. BSSM/ P-LE Perform Loiation Response MAP Subscriber Locatiofi Report Reportack. 13. MAP Subscriber Location 1 1 . BSSMAP Perform Lo( ation Response 15. DTAPLCS MO-LR Return Result 1 6. Release C \A, MIVRR Connec tions Figure 33: General Network Positioning for lUIO-LR £75/ (GSM 03.71 version 8.0.0 Release 1999) 47 ETSI TS 101 724 V8.0.0 (2000-10) 7.6.6.1 Location Preparation Procedure 1) If the MS is in idle mode, the MS requests an SDCCH and sends a DTAP CM service request indicating a request for call independent supplementary services to the BSC. 2) The BSC includes the current cell ID and TA value within the BSSMAP Complete Layer 3 Information message used to convey the CM service request across the A-interface. If the MS is instead in dedicated mode, the MS sends a DTAP CM Service Request on the already established SACCH: the VMSC will then already have been supplied with the current cell ID from either the serving BSC or serving MSC in the case of an established call with MSC-MSC handover. 3) The VMSC instigates authentication and ciphering if the MS was in idle mode or returns a DTAP CM Service Accept if the MS was in dedicated mode. If the target MS supports any MS based or MS assisted positioning method(s), the MS will provide the BSC and MSC with the positioning method(s) it supports via controlled early classmark sending (see GSM 04.08 and 08.08). 4) The MS sends a DTAP LCS MO-LR invoke to the VMSC. If the MS is requesting its own location or that its own location be sent to another LCS client, this message carries LCS QoS information (e.g. accuracy, response time). If the MS is requesting that its location be sent to another LCS client, the message shall include the identity of the LCS client and may include the address of the GMLC through which the LCS client should be accessed. If a GMLC address is not included, the VMSC may assign its own GMLC address and may verify that the identified LCS client is supported by this GMLC. If a GMLC address is not available for this case, the VMSC shall reject the location request. If the MS is instead requesting location assistance data or ciphering keys, the message specifies the type of assistance data or deciphering keys and the positioning method for which the assistance data or deciphering applies. The VMSC verifies in the MS's subscription profile that the MS has permission to request its own location, request that its location be sent to another LCS client or request location assistance data or deciphering keys (whichever applies). If the MS is requesting positioning and has an established call, the VMSC may reject the request for certain non-speech call types. 5) The VMSC sends a BSSMAP-LE PERFORM LOCATION request message to the SMLC associated with the MS's current cell location if the SMLC is NSS based. This message is transported using SCCP connection oriented signaling inside an SCCP Connection Request message The BSSMAP-LE message indicates whether a location estimate or location assistance data is requested and includes the MS's location capabilities and current cell ID. If the MS's location is requested, the message also includes the currently assigned radio channel type (SDCCH, TCH-FR or TCH-HR), the requested QoS and, if available and any location measurement information including the TA value received from the BSC in step 2. If location assistance data is instead requested, the message carries the requested types of location assistance data. 6) If the SMLC is BSS based, the VMSC instead sends the BSSMAP PERFORM LOCATION message to the serving BSC for the target MS. 7) In the case of a BSS based SMLC, the BSC forwards the BSSMAP-LE PERFORM LOCATION request received in step 6 to the SMLC. If the MS's location is requested, the BSC may add additional measurement data to the message to assist with positioning. The message is transported inside an SCCP connection request. 7.6.6.2 Positioning IVIeasurement Establishment Procedure 8) If the MS is requesting its own location, the actions described under step 10 for a MT-LR are performed. If the MS is instead requesting location assistance data, the SMLC transfers this data to the MS as described in subsequent clauses. The SMLC determines the exact location assistance data to transfer according to the type of data specified by the MS, the MS location capabilities and the current cell ID. 7.6.6.3 Location Calculation and Release Procedure 9) When a location estimate best satisfying the requested QoS has been obtained or when the requested location assistance data has been transferred to the MS, the SMLC returns a BSSMAP-LE Perform Location response to the VMSC if the SMLC is NSS based. This message carries the location estimate or ciphering keys if this was obtained. If a location estimate or deciphering keys were not successfully obtained or if the requested location assistance data could not be transferred successfully to the MS, a failure cause is included in the Perform Location response. 10)For a BSS based SMLC, the BSSMAP-LE Perform Location response is instead returned to the serving BSC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 48 ETSI TS 101 724 V8.0.0 (2000-10) 1 l)In the case of a BSS based SMLC, the BSC forwards the BSSMAP PERFORM LOCATION response received in step 10 to the VMSC. 12) If the MS requested transfer of its location to another LCS client and a location estimate was successfully obtained, the VMSC shall send a MAP Subscriber Location Report to the GMLC obtained in step 4 carrying the MSISDN of the MS, the identity of the LCS client, the event causing the location estimate (MO-LR) and the location estimate and its age. 13) The GMLC shall acknowledge receipt of the location estimate provided that is serves the identified LCS client and the client is accessible. 14) The GMLC transfers the location information to the LCS client either immediately or upon request from the client. 15) The VMSC returns a DTAP LCS MO-LR Return Result to the MS carrying any location estimate requested by the MS, ciphering keys or a confirmation that a location estimate was successfully transferred to the GMLC serving an LCS client. 16) The VMSC may release the CM, MM and RR connections to the MS, if the MS was previously idle, and the VMSC may record billing information. 7.7 Common Procedures to Support Positioning The procedures described in this clause enable an SMLC to obtain positioning related information or instigate positioning for a particular target MS. The procedures are applicable to all positioning methods after an SMLC receives a BSSMAP-LE Perform Location request for a target MS until a BSSMAP-LE Perform Location response is returned to the originator. 7.7.1 Information Transfer between an NSS basecj SIVILC ancj a Target IVIS An NSS based SMLC uses the procedure shown in figure 34 in order to obtain positioning information from a target MS or transfer location assistance information to a target MS after a request has been received from the VMSC. More details of the location information transfer procedure between the BSC and MS can be found in GSM 04.08. SIVLC VMSC 1 . BSSMAP-LE Connection Oriented infonration [BSSLAP IVIS Position Command [RRLP message]] 6. BSSMAP-LE Connection Orient 3d Infonration [BSSLAP MS Positia i Response [RRLP mess^eH BSC Z BSSMAP Connection Orient 3d Information [BSSLAP MS Po; ition Command [RRLP message]] 3. RR Application Informati [RRLP message] 5. BSSMAP Connection Orient sd Information [BSSLAP MS Po; ition Response [RRLP message]] MS Dn 4. RR Application lnformati|on [RRLP message] Figure 34: Information Transfer between an NSS based SIVILC and a Target MS £75/ (GSM 03.71 version 8.0.0 Release 1999) 49 ETSI TS 101 724 V8.0.0 (2000-10) 1) The SMLC passes a BSSMAP-LE Connection Oriented Information message to the VMSC containing an embedded BSSLAP MS Position Command with an RRLP message parameter. The message is transferred using the SCCP connection established between the SMLC and VMSC for positioning the target MS. If the BSSLAP message is too large to fit in a single BSSMAP-LE Connection Oriented Information message, it may be segmented and transferred inside a sequence of BSSMAP-LE messages with the last BSSMAP-LE message containing a last segment indication and the last BSSLAP segment. The SMLC shall indicate in the BSSLAP MS Position Command whether the embedded RRLP message contains a positioning command, versus positioning assistance data. 2) The VMSC forwards the BSSMAP message(s) to the serving BSC for the target MS. 3) The BSC transfers the embedded RRLP message to the target MS inside an RR Application Information message. If the BSSLAP message was segmented by the SMLC, onward transfer to the MS shall be deferred until all segments have arrived and the complete BSSLAP message is reassembled. The embedded RRLP message shall then be re-segmented if necessary with each RRLP segment transferred in a separate RR Application Information message with the last RR message indicating the last RRLP segment. No later than when the last RR Application Information message has been transferred, the BSC shall start a positioning supervision timer if none is already in progress or restart this if already in progress. If the timer expires before the final response in step 4 is received, the BSC shall return a BSSMAP-LE Connection oriented Information message to the SMLC containing a BSSLAP Abort with a cause of BSC timeout. 4) When the target MS has positioning information to return to the SMLC, it sends an RR Application Information message to the BSC containing an embedded RRLP message. If the RRLP message is too large to fit in a single RR Application Information message, it may be segmented and carried in a sequence of RR Application Information messages with the last message indicating the last RRLP segment. The last RR LCS Information message shall indicate if this is the final response from the MS. 5) If the timer started in step 3 has already expired, the BSC discards the RRLP message received in step 4. Otherwise, the BSC forwards the RRLP message to the VMSC inside a BSSLAP MS Positioning Response message contained in a BSSMAP Connection Oriented Information message. If the RRLP message was segmented onward transfer to the MSC shall be deferred until all segments have arrived and the complete RRLP message is reassembled. If the resulting BSSLAP message is too large to fit into a single BSSMAP Connection Oriented Information message (e.g. if the RRLP message was segmented), it shall be segmented. Each segment is then transferred in a separate BSSMAP message with the last message containing the last BSSLAP segment. If the SMLC indicated a positioning command in step 1 and the MS has indicated a final response, the BSC may add additional measurement information to the BSSLAP MS Position Response in the last BSSMAP message - if necessary, creating a new BSSMAP message if message size limitations would be exceeded. The BSC shall stop the supervision timer started in step 3 when the final segment of the final response from the MS has been transferred. 6) The VMSC forwards the received BSSMAP messages as corresponding BSSMAP-LE message(s) to the SMLC using the SCCP connection previously established for positioning the target MS. If the MS did not indicate a final response in step 3, the SMLC may transfer a further RRLP message to the MS (e.g. containing assistance data) according to steps 1 to 3 and the MS may return a subsequent response according to steps 4 to 6. 7.7.2 Information Transfer between a BSS based SMLC and a Target MS A BSS based SMLC uses the procedure shown in figure 35 in order to obtain positioning measurements from a target MS or transfer location assistance information to a target MS after a request has been received from the BSC serving the target MS. More details of the location information transfer procedure between the BSC and MS can be found in GSM 04.08. £75/ (GSM 03.71 version 8.0.0 Release 1999) 50 ETSI TS 101 724 V8.0.0 (2000-10) SMLC BSC 1. BSSMAP-LE Connection Orientec Information [BSSLAP MS Position Command [RRLP message]] 4. BSSMAP-LE Connection Orientec Information [BSSLAP IVIS Position Response [RRLP message]] MS 2. RRAppiication rnftrmation [RRLP message] 3. RR Application [RRLP message] Informaticn Figure 35: Information Transfer between a BSS based SIUILC and a Target lUIS 1) The SMLC passes a BSSMAP-LE Connection Oriented Information message to the serving BSC containing an embedded BSSLAP MS Position Command with an RRLP message parameter. The message is transferred using the SCCP connection estabHshed between the SMLC and BSC for positioning the target MS If the BSSLAP message is too large to fit in a single BSSMAP-LE Connection Oriented Information message, it may be segmented and transferred inside a sequence of BSSMAP-LE messages with the last BSSMAP-LE message containing a last segment indication and the last RRLP segment. The SMLC shall indicate in the first BSSLAP MS Position Command whether the embedded RRLP message contains a positioning command, versus positioning assistance data. 2) The BSC transfers the embedded RRLP message to the target MS inside an RR Application Information message. If the BSSLAP message was segmented by the SMLC, onward transfer to the MS shall be deferred until all segments have arrived and the complete BSSLAP message is reassembled. The embedded RRLP message shall then be re-segmented if necessary with each RRLP segment transferred in a separate RR Application Information message with the last RR message indicating the last RRLP segment. No later than when the last RR Application Information message has been transferred, the BSC shall start a positioning supervision timer if none is already in progress or restart this if already in progress. If the timer expires before the final response in step 3 is received, the BSC shall return a BSSMAP-LE Connection oriented Information message to the SMLC containing a BSSLAP Abort with a cause of BSC timeout. 3) When the target MS has positioning information to return to the SMLC, it sends an RR Application Information message to the BSC containing an embedded RRLP message. If the RRLP message is too large to fit in a single RR Application Information message, it may be segmented and carried in a sequence of RR Application Information messages with the last message indicating the last RRLP segment. The last RR Application Information message shall indicate if this is the final response from the MS. 4) If the timer started in step 2 has already expired, the BSC discards the RRLP message received in step 3. Otherwise, the BSC forwards the RRLP message to the SMLC inside a BSSLAP MS Positioning Response message contained in a BSSMAP-LE Connection Oriented Information message. If the RRLP message was segmented, onward transfer to the SMLC shall be deferred until all segments have arrived and the complete RRLP message is reassembled. If the resulting BSSLAP message is too large to fit into a single BSSMAP-LE Connection Oriented Information message (e.g. if the RRLP message was segmented), it shall be segmented. Each segment is then transferred in a separate BSSMAP-LE message with the last message containing the last BSSLAP segment. If the SMLC indicated a positioning command in step 1 and the MS has indicated a final response, the BSC may add additional measurement information to the BSSLAP MS Position Response in the last BSSMAP-LE message - if necessary, creating a new BSSMAP-LE message if message size limitations would be exceeded. The BSC shall stop the supervision timer started in step 2 when the final segment of the final response from the MS has been transferred. If the MS did not indicate a final response in step 2, the SMLC may transfer a further RRLP message to the MS (e.g. containing assistance data) according to steps 1 and 2 and the MS may return a subsequent response according to steps 3 and 4. 7.7.3 Information Transfer between an NSS based SMLC and a BSC An NSS based SMLC uses the procedure shown in figure 36 in order to obtain positioning related information for a particular target MS from the BSC after a positioning request has been received from the VMSC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 51 ETSI TS 101 724 V8.0.0 (2000-10) SMLC VMSC 1.SCCPDT1 [BSSMAP Connection Oriented Information] 4. SCCP DTI [BSSMAP Connection Oriented Information] SjCOP DTI [BSSIVIAP-LE Co inection Oriented Informatic n] BSC >-LEC ;CCP DT1 [BSSMAP-LE Connection Oriented Information Figure 36: Information Transfer between an NSS based SIVILC and a BSC 1) The SMLC passes a BSSMAP Connection Oriented Information message to the VMSC containing an embedded BSSLAP message. The BSSMAP message is transferred using the SCCP connection previously estabHshed between the SMLC and MSC when the positioning request for the target MS was initially sent to the SMLC. 2) The VMSC forwards the BSSMAP-LE message to the BSC serving the target MS. The BSC recognizes that it is the final destination due to the presence of the embedded BSSLAP message. 3) When the BSC has positioning information for the target MS to return to the SMLC, it sends a BSSMAP-LE Connection Oriented Information message to the VMSC containing an embedded BSSLAP message. 4) The VMSC forwards the BSSMAP message to the SMLC using the SCCP connection previously established for positioning the target MS. 7.7.4 Information Transfer between a BSS based SMLC and a BSC A BSS based SMLC uses the procedure shown in figure 37 in order to obtain positioning related information from the BSC serving a particular target MS after a positioning request has been received from the BSC. SMLC BSC 1 . SCCP DTI [BSSMAP-LE Connectii Oriented Infornnation] 2 SCCP DTI [BSSMAP-LE Connectii Oriented Infornnation] Figure 37: Information Transfer between a BSS based SMLC and a BSC 1) The SMLC passes a BSSMAP-LE Connection Oriented Information message to the BSC containing an embedded BSSLAP message. The BSSMAP-LE message is transferred using the SCCP connection previously established between the SMLC and BSC when the positioning request for the target MS was initially sent to the SMLC. The BSC recognizes that it is the final destination due to the presence of the embedded BSSLAP message. 2) When the BSC has positioning information for the target MS to return to the SMLC, it sends a BSSMAP-LE Connection Oriented Information message to the SMLC containing an embedded BSSLAP message. The message is sent using the SCCP connection previously established for positioning the target MS. 7.8 Common Procedures to Support Access to an LMU The procedures in this clause support the transfer of positioning related information and O&M data between an SMLC and a particular LMU associated with the SMLC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 52 ETSI TS 101 724 V8.0.0 (2000-10) 7.8.1 Information Transfer between an NSS basecJ SMLC anci a Type A LMU 7.8.1.1 Information Transfer using an SDCCH SMLC VMSC l.BSSAP-LELMU Connection Request 3. BSSAP-LE LMU Connection Accept 4. DTAP-LE EtEGISTER, FACILITY c RELEASE COMPLETE 6. BSSAP-LE LMU Connection Release 10. BSSAP-LE LMU Connection Request 11. BSSAP-LE LMU Connection Accept 14. DTAP-LE REGISTER, FACILITY or RELEASE COMPLETE BSC 2. LMU Paging Authei tication, Ciphering 5. DTAP-LE REGI! TER, FACILITY c RELEASE COM >LETE 7. Release Signalii 9. Complete L3 Informatio i [DTAP CM Sei-vice Rec test] 12. Authenticat an, Cipheiing 13. DTAP-LE REGIS TER, FACILITY c RELEASE COMI LETE LMU 8. DTAP CM Service Rec uest Figure 38: Information Transfer between an NSS based SIUILC and a Type A LIUlU using an SDCCIH 1) If there is no SCCP connection yet for an LMU between the SMLC and the MSC serving the LMU, the SMLC sends a BSSMAP-LE LMU connection request message to the MSC contained in an SCCP Connection Request. The BSSMAP-LE message shall contain the IMSI of the LMU and shall indicate whether authentication of the LMU is needed and/or ciphering. 2) For an LMU that has no main signaling link to the MSC (e.g. LMU uses a temporary SDCCH), the serving MSC performs paging to assign an SDCCH. The Channel Request message requesting an SDCCH that is sent by the LMU in response to the Paging Request shall contain an LMU establishment cause. The MSCA'LR also performs authentication and/or ciphering if requested by the SMLC. 3) The serving MSC returns a BSSMAP-LE LMU Connection Accept to the SMLC. If the paging or authentication in step 2 failed, the MSC returns a BSSMAP-LE LMU Connection Reject message. 4) If the SMLC needs to send data to the LMU, it may send one or more DTAP-LE REGISTER, FACILITY and RELEASE COMPLETE messages to the serving MSC using the SCCP connection established in steps 1 to 3. Each DTAP-LE message may carry an embedded LLP message and an indication of whether release of the SDCCH by the LMU is forbidden. 5) The serving MSC passes each DTAP-LE message received from the SMLC in step 4 to the LMU. £75/ (GSM 03.71 version 8.0.0 Release 1999) 53 ETSI TS 101 724 V8.0.0 (2000-10) 6) The SMLC may initiate release of the SDCCH to the LMU and the associated SCCP connection to the MSC by sending a BSSMAP-LE LMU Connection Release message. 7) For an LMU that has no other active MM and CM connections, the MSC initiates release of the SDCCH. 8) When the LMU has LCS data to send and does not currently have a signaling link, it sends an RR Channel request to the serving BTS to request an SDCCH. The RR Channel Request contains an establishment cause identifying an LMU. After assignment of the SDCCH, the LMU sends a DTAP CM Service request to the serving BSC to request an MM connection for location services. 9) The serving BSC passes the CM Service Request to the VMSC with an indication that this came from an LMU inside a Complete layer 3 Information message. 10)The serving MSC sends a BSSMAP-LE LMU Connection Request message to the SMLC associated with the LMU inside an SCCP connection request (e.g. use IMSI or LAC association to determine the SMLC). The BSSMAP-LE message shall contain the IMSI of the LMU and the address of the MSC. 1 l)The SMLC returns a BSSMAP-LE LMU Connection Accept, to the MSC indicating if authentication or ciphering are required. 12)The serving MSC performs authentication and ciphering if requested by the SMLC. Otherwise, a CM Service Accept is returned. 13) The LMU sends one or more DTAP-LE REGISTER, FACILITY and RELEASE COMPLETE messages to the serving MSC each containing an embedded LLP message. 14)The serving MSC passes each DTAP-LE message to the SMLC using the SCCP connection established in steps lOto n. 7.8.1.2 Information Transfer using a TCH SMLC VMSC 1. Establish SDCCH and 2. SS7 ISUP lAM BSC SCCP Signaling Conne LMU 3. Existing procedure to setup an incoming call 4. SS7ISUPANM 5. SCCP RLSD 7. SS7 ISUP REL 8. SS7 ISUP PLC 6. DTAP- .E LCS Information 9. Existing procedure for call release \ Figure 39: Information Transfer between an NSS based SIVILC and a Type A LIUlU using a TCH 1) The SMLC or LMU establishes a signaling connection to the other entity using an SDCCH. The VMSC provides the SMLC with a called number identifying the LMU in the BSSMAP-LE LMU Connection Request or Accept £75/ (GSM 03.71 version 8.0.0 Release 1999) 54 ETSI TS 101 724 V8.0.0 (2000-10) 2) The SMLC sends an ISUP lAM to the VMSC with the called number from step 1 in the called party number. The lAM contains the required bearer capability and references a 64 Kbps trunk connection between the SMLC and the VMSC. The VMSC may verify that the SMLC is the source of the JAM from the SS7 link on which the lAM is received (with dedicated links on the Ls interface), the SS7 OPC in the MTP routing label or the referenced trunk connection. 3) The VMSC establishes an incoming call to the LMU with the requested bearer capability using the existing procedure defined in GSM 04.08. For this procedure, an ALERTING message from the LMU shall not be used. 4) The VMSC confirms the call establishment to the SMLC - the TCH is through connected to the 64 Kbps trunk indicated in step 2. 5) The VMSC initiates release of the SCCP connection to the SMLC established in step 1 by sending an SCCP Released message. 6) DTAP-LE REGISTER, FACILITY and RELEASE COMPLETE messages are transferred between the SMLC and LMU on the established TCH: these are transparent to the VMSC and BSC. 7) The SMLC initiates release of the TCH by sending an ISUP REL to the VMSC. 8) The SMLC acknowledges the release request. 9) The VMSC releases the call and the TCH to the LMU using the existing procedure defined in GSM 04.08. 7.8.2 Location UpcJate Procedure between a BSS based SMLC and a Type A LMU The following procedure supports a normal GSM location update from the perspective of a type A LMU. The location update can occur periodically, on power up, following recovery from some failure condition and when an LMU in idle mode detects that its closest BTS is in another location area. A subscription of the LMU in an HLR is not needed if this procedure is supported by the SMLC. SMLC BSC 2. SCCPCR[BSSMAP Corr plete Layer 3 Information [Location Updating Request]] 3. Normal GSM Autt 4. DTAP Location Updating Accept LMU 1. DTAP Location Updating Request entication, Ciphering 5. DTAP Location Updatin 5 Accept Figure 40: Location Update Procedure between a BSS based SIVILC and a Type A LIVIU 1) If the LMU does not currently have a signaling link, it sends an RR Channel Request to the serving BTS to request an SDCCH. The RR Channel Request contains an establishment cause identifying an LMU. After assignment of the SDCCH, the LMU sends a DTAP Location Updating request to the BSC. This shall indicate that a follow on request is pending if the LMU has more data to send. 2) Because the BSC serving the LMU is associated with a BSS based SMLC and the Channel Request message contained an LMU establishment cause, the BSC forwards the Location Updating request to the SMLC rather than MSC. If there was previously no SDCCH, this is sent inside a BSSMAP Complete Layer 3 Information message that is contained in an SCCP Connection Request. 3) The SMLC performs existing GSM authentication and ciphering if needed for the LMU. The SMLC shall not assign a TMSI to the LMU to avoid duplicating a TMSI assigned to a normal MS by a VLR. £75/ (GSM 03.71 version 8.0.0 Release 1999) 55 ETSI TS 101 724 V8.0.0 (2000-10) 4) The SMLC returns a DTAP Location Updating Accept to the BSC. Unless the LMU indicated a follow on request, the SMLC may then initiate release of the SDCCH. 5) The BSC forwards the DTAP message to the LMU. 7.8.3 IMSI Detach Procedure between a BSS based SMLC and a Type A LMU The following procedure supports a normal GSM IMSI Detach from the perspective of a type A LMU. This may be instigated if the LMU is to be deactivated - e.g. for offline maintenance. SMLC BSC 2. SCCPCR[BSSMAP Cor iplete Layer 3 Information [IMSI Detact Indication]] LMU 1 . DTAP IMSI Detach Indie ation Figure 41 : IIUISI Detach Procedure between a BSS based SIUILC and a Type A LIUlU 1) If the LMU does not currently have a signaling link, it sends an RR Channel Request to the serving BTS to request an SDCCH. The RR Channel Request contains an establishment cause identifying an LMU. After assignment of the SDCCH, the LMU sends a DTAP IMSI Detach Indication to the BSC. 2) Because the BSC serving the LMU is associated with a BSS based SMLC and the Channel Request message contained an LMU establishment cause, the BSC forwards the IMSI Detach Indication to the SMLC rather than MSC. If there was previously no SDCCH, this is sent inside a BSSMAP Complete Layer 3 Information message that is contained in an SCCP Connection Request. The SMLC marks the LMU as temporarily inactive and initiates release of the SDCCH. £75/ (GSM 03.71 version 8.0.0 Release 1999) 56 ETSI TS 101 724 V8.0.0 (2000-10) 7.8.4 LCS Information Transfer between a BSS basecj SMLC an6 a Type ALMU 7.8.4.1 Information Transfer using an SDCCH The following procedure supports information transfer between a BSS based SMLC and a type A LMU. SMLC BSC 1 . SCCP UDT [BSSMAP P iging] 4. SCCP CR [Complete layer 3 Information [RR Paging Re sponse]] 5. Authentic ition, Cipliering 6. SCCP DTI [DTAP-LE REGfSTER, FACILITY or RELEASE COMPLETE] 7. SCCP DT1 [BSSMAP ( ;lear Command] 10. SCCPRLSD 12. SCCPCR[BSSMAP Corr plete Layer 3 Information [CM Ser 'ice Request]] 13. Autinenticaticn, Cipinering 14. SCCP DTI [DTAP-LE REGISTER, FACILITY or RELEASE COMPLETE LMU 2. RR Paging Request 3. RR Paging Response 8. SCCP DTI [BSSMAP Cjlear Complete] 9. RR Channel Rel^ 1 1 . DTAP CM Service Reqi est Figure 42: Information Transfer between a BSS based SIVILC and a Type A LIVIU 1) If there is no signaling link yet for an LMU between the SMLC and the BSC serving the LMU, the SMLC sends a BSSMAP Paging message to the serving BSC inside an SCCP Unitdata message. 2) The serving BSC broadcasts an RR Paging Request. 3) The LMU sends a Channel Request message containing an LMU establishment cause to request an SDCCH. After assignment of the SDCCH, the LMU returns an RR Paging Response. 4) Because the BSC serving the LMU is associated with a BSS based SMLC and the Channel Request message in step 3 contained an LMU establishment cause, the BSC transfers the Paging Response to the SMLC, rather than MSC, in a BSSMAP Complete Layer 3 Information message contained in an SCCP Connection Request. 5) The SMLC performs normal GSM authentication and ciphering if this is needed for the LMU. The SMLC shall not assign a TMSI to the LMU to avoid duplicating a TMSI assigned to a normal MS by a VLR. 6) If the SMLC needs to send data to the LMU, it may send one or more DTAP-LE REGISTER, FACILITY or RELEASE COMPLETE messages to the BSC. Each DTAP-LE message contains an embedded LLP message and an indication of whether release of the SDCCH by the LMU is forbidden. Each DTAP-LE message is transferred by the BSC to the LMU. £75/ (GSM 03.71 version 8.0.0 Release 1999) 57 ETSI TS 101 724 V8.0.0 (2000-10) 7) The SMLC may initiate release of the SDCCH to the LMU by sending a BSSMAP Clear Command to the BSC. 8) The BSC returns a BSSMAP Clear Complete. 9) The BSC orders release of the SDCCH by sending an RR Channel Release to the LMU. 10)The SMLC releases the SCCP connection to the BSC by sending an SCCP Released message. 1 1) When the LMU has LCS data to send and does not currently have a signaling link, it sends an RR Channel Request to the serving BTS to request an SDCCH. The RR Channel Request contains an establishment cause identifying an LMU. After assignment of the SDCCH, the LMU sends a DTAP CM Service request to the serving BSC. 12)Because the BSC serving the LMU is associated with a BSS based SMLC and the Channel Request message contained an LMU establishment cause, the BSC forwards the CM Service Request with an indication that this came from an LMU to the SMLC, rather than MSC, inside a BSSMAP Complete Layer 3 Information message that is contained in an SCCP Connection Request. 13) The SMLC performs authentication and ciphering if needed for the LMU. Otherwise, a CM Service Accept is returned. The SMLC shall not assign a TMSI to the LMU to avoid duplicating a TMSI assigned to a normal MS by a VLR. 14) The LMU sends one or more DTAP-LE REGISTER, FACILITY or RELEASE COMPLETE messages to the serving BSC each containing an embedded LLP message. The BSC forwards each DTAP-LE message to the SMLC. 7.8.4.2 Information Transfer using a TCH SMLC BSC 1 . Setup Signaling Cor lection using an SDCCH 2. DTAF Setup 3. DTAP Ca Confirmed 4. Assignment Request 7. Assignment CompI 8. DTAP 9. DTAP C( nnecl!\cl<. 1 1 . DTAP I Jisconnect 1 2. DTAF Release 13. DTAP Release Complete 14. SCCP DTI [BSSIVIAP (Clear Command] 4 15. SCCP DTI [BSSMAP C lear Complete] 17. SCCPRLSD LMU 5. RR Assignment Commapd 6. RR Assignment Comple:e Connect 10. DTAP-LE LCS Conns ctlon Oriented Information 16. RR Channel Rel^Sf ^ Figure 43: Information Transfer between a BSS based SIVILC and a Type A LIVIU using a TCH £75/ (GSM 03.71 version 8.0.0 Release 1999) 58 ETSI TS 101 724 V8.0.0 (2000-10) 1) The SMLC establishes a signahng connection to the LMU using an SDCCH. 2) The SMLC sends a DTAP Setup to the LMU with the requested bearer capabihty. 3) The LMU returns a DTAP Call Confirmed. 4) The SMLC initiates traffic channel assignment by sending a BSSMAP Assignment Request to the BSC. 5) The BSC requests channel activation in the BTS and then sends an RR Assignment Command to the LMU. 6) The LMU acknowledges TCH assignment. 7) The BSC confirms TCH assignment. 8) The LMU confirms call establishment. 9) The SMLC acknowledges the LMU confirm. 10) DTAP -LE Connection Oriented Information messages are transferred between the SMLC and LMU on the established TCH: these are transparent to the BSC. 1 l)The SMLC initiates release of the TCH by sending a DTAP Disconnect to the LMU 12)The LMU returns a DTAP Release. 13) The SMLC sends a DTAP Release Complete. 14) The SMLC initiates release of the TCH by sending a BSSMAP Clear Command to the BSC. 15)The BSC returns a BSSMAP Clear Complete. 16) The BSC orders release of the TCH by sending an RR Channel Release to the LMU. 17) The SMLC releases the SCCP connection to the BSC by sending an SCCP Released message. 7.8.5 Information Transfer between an NSS based SMLC and a Type B LMU An NSS based SMLC uses the procedure shown in figure 44 in order to exchange LCS information with a type B LMU. SMLC VMSC 1. SCCP UDT [BSSMAP-LE Connectionless Information] 6. SCCP UDT [BSSMAP-LE Connectionless Information] BSC 2. SCCP UDT [BSSMk\P-LE Connectionless Information] 5. SCCP UDT [BSSMAP-LE Connectionless Information] BTS or LMU 3. 08.58 Location In- ormation 4. 08.58 Location Inl ormation Figure 44: Information Transfer between an NSS based SIUILC and a Type B LIUlU 1) The SMLC passes a BSSMAP-LE Connectionless Information message to the VMSC containing an embedded LLP message and the LAC/CI cell address identifying the LMU. The BSSMAP-LE message is transferred inside an SCCP Unitdata message. 2) The VMSC forwards the BSSMAP-LE message to the BSC serving the LAC/CI address. £75/ (GSM 03.71 version 8.0.0 Release 1999) 59 ETSI TS 101 724 V8.0.0 (2000-10) 3) The BSC transfers the embedded RRLP message to either the BTS associated with the LMU or the LMU itself inside an 08.58 LCS Information message. The BTS or LMU is identified using the LAC/CI received in step 2. 4) When the LMU has positioning information to return to the SMLC, either it or its associated BTS transfers this to the BSC inside an 08.58 LCS Information message. 5) The serving BSC forwards the RRLP message to the VMSC inside a BSSMAP-LE Connectionless Information message contained in an SCCP Unitdata message. The BSSMAP-LE message contains the LAC/CI address identifying the LMU. 6) The VMSC forwards the BSSMAP-LE message to the SMLC in an SCCP Unitdata message. 7.8.6 Information Transfer between a BSS based SMLC ancJ a Type B LMU A BSS based SMLC uses the procedure shown in figure 45 in order to exchange LCS information with a type B LMU. SMLC BSC 1. SCCP UDT [BSSMAP-LE Connectionless Information] 4. SCCP UDT [BSSMAP-LE Connectionless Information] BTS or LMU 2. 08.58 Location Infcrmation 3. 08.58 Location Infc rmation Figure 45: Information Transfer between a BSS based SIUILC and a Type B LIVIU 1) The SMLC passes a BSSMAP-LE Connectionless Information message to the BSC containing an embedded LLP message and the LAC/CI cell address identifying the LMU. The BSSMAP-LE message is transferred inside an SCCP Unitdata message. 2) The BSC transfers the embedded LLP message to either the BTS associated with the LMU or the LMU itself inside an 08.58 LCS Information message. The BTS or LMU is identified using the LAC/CI received in step 1. 3) When the LMU has positioning information to return to the SMLC, either it or its associated BTS transfers this to the BSC inside an 08.58 LCS Information message. 4) The serving BSC forwards the LLP message to the SMLC inside a BSSMAP-LE Connectionless Information message contained in an SCCP Unitdata message. The BSSMAP-LE message contains the LAC/CI address identifying the LMU. 7.9 Common Control Procedures for LMUs The procedures in this clause are applicable to any Type A LMU and may be used for any Type B LMU to enable control of the LM by its associated SMLC. The procedures assume support for the establishment of a signaling link and the transfer of LLP messages between an SMLC and LMU that are defined in clause 7.8. Consequently, details of signaling link establishment and message transfer by an intermediate MSC, BSC and BTS are not shown. £75/ (GSM 03.71 version 8.0.0 Release 1999) 60 ETSI TS 101 724 V8.0.0 (2000-10) 7.9.1 Reset Procecdure The reset procedure enables an SMLC to return an LMU to a known initial state in which no measurement or O&M operations are outstanding or being performed. SMLC MSC/VLR 1. LLP Reset Invoke message BSC LMU 2. LLP Res et Return Result Figure 46: Reset Procedure for a Circuit lUlode LIUlU 1) After first establishing a signaling connection to the LMU (see clause 7.8), the SMLC sends an LLP Reset Invoke to the LMU via an intermediate MSC and/or BSC. 2) The LMU cancels any LCS measurement and O&M tasks previously ordered by the SMLC. The LMU then returns an LLP Reset Return Result to the SMLC. 7.9.2 Status Query Procedure The Status Query procedure enables an SMLC to verify the status of an associated LMU. The procedure may be instigated periodically or following any loss of communication with the LMU. SMLC MSC/VLR 1 . LLP Status Quer) 2. LLP Status BSC Invoke message Query Return Result LMU Figure 47: Status Query Procedure for a Circuit lUlode LIUlU 1) After first establishing a signaling connection to the LMU (see clause 7.8), the SMLC sends an LLP Status Query Invoke to the LMU via an intermediate MSC and/or BSC. 2) The LMU returns an LLP Status Query return result, indicating the number of active measurement jobs for each type of measurement (e.g. RIT, TO A) and the number of active O&M jobs in the LMU that were previously ordered by the SMLC. 7.9.3 Status Update Procedure The Status Update procedure enables an LMU to report status information to its associated SMLC. For a Type A LMU with an associated NSS based SMLC, instigation of the procedure also provides the SMLC with the identity of the MSC currently serving the LMU. The procedure may be instigated for the following reasons: 1 . Periodically 2. Power-on condition or recovery from failure with loss of memory 3. Impending availability or unavailability for O&M reasons 4. Location Update by a Type A LMU in a new Location Area. £75/ (GSM 03.71 version 8.0.0 Release 1999) 61 ETSI TS 101 724 V8.0.0 (2000-10) SMLC MSC/VLR 1 . LLP Status Update 2. LLP Status Update BSC Invoke message Return Result LMU Figure 48: Status Update Procedure for a Circuit lUlode LIUlU 1) After first establishing a signaling connection to the SMLC (see clause 7.8), the LMU sends an LLP Status Update Invoke to the SMLC via an intermediate MSC and/or BSC. This message shall include the reason for the Status Update, the number of active and outstanding jobs of each category in the LMU and the current hardware status. 2) The SMLC returns an LLP Status Update return result to acknowledge receipt of the Status Update. 7.10 Common Procedures supporting Interaction between Peer SIVILCs 7.1 0.1 Information Transfer between Peer SMLCs Figure 49 illustrates LCS information transfer between peer SMLCs where, in this scenario, one SMLC is NSS based and the other BSS based. It is assumed that while the NSS based SMLC has SS7 Hnks to an STP, the ESS based SMLC does not. NSS SMLC MSC 1.SCCPUDT [BSSMAP-LE Connectionless Information] 6. SCCP UDT [BSSMAP-LE Connectionless Information] BSC 2. SCCP UDT [BSSM^VP Connectionless Information] 5. SCCP UDT [BSSI\jlAP Connectionless Info mation] BSS SMLC 3. SCCP UDT [BSSIVAP-LE Connectionless Info 'mation] 4. SCCP UDT [BSSMAP-LE Connectionless Information] Figure 49: Information Transfer between an NSS based and a BSS based SIVILC 1) When the NSS based SMLC has LCS information to send to another SMLC, it transmits a BSSMAP-LE Connectionless Information message containing an embedded SMLCPP message and the LAC/CI cell address identifying the other SMLC. If an SMLCPP message is too large to fit in a single BSSMAP-LE Connectionless Information message, it may be segmented and transferred inside a sequence of BSSMAP-LE messages. The BSSMAP-LE message is transferred inside an SCCP Unitdata message. The message is routed to an SS7 signaling point code associated with the LAC/CI address. In this scenario, the signaling point code is that for the MSC connected to the BSC for the BSS based SMLC. 2) The MSC forwards the BSSMAP message or a message segment to the BSC associated with the LAC/CI address received in step 1 . 3) The BSC transfers the BSSMAP-LE message or a message segment to the SMLC. The BSC recognizes the SMLC as the final destination due to the presence of the embedded SMLCPP message. £75/ (GSM 03.71 version 8.0.0 Release 1999) 62 ETSI TS 101 724 V8.0.0 (2000-10) 4) When the BSS based SMLC has positioning information to return to the NSS based SMLC, it passes this to its associated BSC in a BSSMAP-LE Connectionless message contained in an SCCP Unitdata message. The BSSMAP-LE message contains an embedded SMLCPP message and the LAC/CI address identifying the other SMLC. If an SMLCPP message is too large to fit in a single BSSMAP-LE message, it may be segmented and transferred inside a sequence of BSSMAP-LE messages. 5) The serving BSC forwards the BSSMAP message or a message segment to its MSC. 6) The MSC forwards the BSSMAP-LE message or a message segment directly to the NSS based SMLC in an SCCP Unitdata message. The message is routed to an SS7 signaling point code associated with the LAC/CI address in the BSSMAP-LE message. In this scenario, the signaling point code is that for the NSS based SMLC. 7.11 Exception Procedures The procedures in this clause apply to all variants of an MT-LR, NI-LR and MO-LR where a BSSMAP-LE Perform Location Request has been sent to an SMLC by a BSC or MSC requesting some location service (e.g. provision of a location estimate for a target MS or transfer of assistance data to a target MS). 7.11.1 Procedures in the SMLC When a request for a location estimate fails due to failure of a position method itself (e.g. due to inaccurate or insufficient position measurements and related data) and the SMLC is unable to instigate another positioning attempt (e.g. due to a requirement on response time), the SMLC may return a BSSMAP-LE Perform Location response containing a less accurate location estimate (e.g. based on serving cell and timing advance). If a less accurate estimate is not available or will not meet the accuracy requirement, the SMLC shall instead return a BSSMAP-LE Perform Location response message containing no location estimate and indicating the cause of failure. When a request for any other location service (e.g. transfer of assistance data to a target MS) fails for any reason and the SMLC is unable to reattempt the service, the SMLC shall return a BSSMAP-LE Perform Location response message indicating the cause of failure. When a location service request is interrupted by some other unrecoverable error event inside the SMLC, the SMLC shall immediately terminate the location service attempt and return a BSSMAP Perform Location Response message containing the reason for the location service cancellation. In that case, any dialogue previously opened with an LMU or BSC for the purpose of instigating position measurements for any MS being located may also be aborted by the SMLC. If the SMLC receives a BSSMAP-LE Perform Location Abort indication for a previous location service request from the VMSC (NSS based SMLC) or BSC (BSS based SMLC), it shall immediately terminate the location service attempt and may abort any dialogues used for the location service attempt that may still exist with any LMUs. Although the SMLC cannot abort any location procedure instigated in the serving BSC (e.g. for TO A), the circumstances of the abort may still ensure cancellation of any such procedure (see clause on BSC). If the SMLC has instigated any location releated procedure in the Target MS or its serving BSC and receives a BSSLAP Reject, BSSLAP Abort or BSSLAP Reset indication from the BSC, it shall cancel the location service attempt and may abort any dialogues for this that currently exist with any LMUs. For a BSSLAP Abort, the SMLC shall then either return any location estimate already derived, if this was requested and is sufficient for the requested QoS, or return a BSSMAP-LE Perform Location response indicating failure of the location service and the cause of the failure in the BSSLAP Abort. For a BSSLAP Reject and BSSLAP Reset, the SMLC has the additional option of restarting the location service attempt and using the same or a different position method where a location estimate was requested. A decision to restart the location service shall take into account the cause of the location service failure as conveyed in the BSSLAP Reject or BSSLAP Reset and whether, in the case of successful intra-BSC handover, the new cell for the target MS is still associated with the SMLC. If the SMLC receives a BSSLAP Reject or BSSLAP Reset with a cause indicating intra-BSC handover and with a new cell identity for the target MS that is not associated with the SMLC, the SMLC shall return a BSSMAP-LE Perform Location response containing either a location estimate, if requested, available and sufficient for the requested QoS, or a failure cause indicating "intra-BSC" handover. NOTE: This procedure may only be needed for an NSS-based SMLC. The SMLC may indicate an inability to support location due to overload by rejecting with a cause indicating congestion a BSSMAP-LE Perform Location request received from either an MSC or BSC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 63 ETSI TS 101 724 V8.0.0 (2000-10) 7.11.2 Procecdures in the VMSC After the VMSC has requested a location service for a particular MS from the SMLC or BSC, certain events may occur that may temporarily or permanently interfere with the location service. For each such event notified to the VMSC, the VMSC shall employ one of the following error recovery actions. Restart the Location Service This action shall be employed for any event that temporarily impedes a location service attempt and cannot be delayed until the location service attempt is complete. When such an event is notified to the VMSC, it shall immediately cancel the location service attempt and the associated BSSMAP-LE or BSSMAP dialogue with the SMLC (NSS based SMLC) or BSC (BSS based SMLC), respectively, if this still exists by sending a BSSMAP-LE or BSSMAP Perform Location Abort message to the SMLC or BSC, respectively. The Abort message shall contain the reason for the location procedure cancellation. After aborting the location request dialogue with the SMLC or BSC, the VMSC may queue the location service request until the event causing the restart has terminated (if not already terminated). The VMSC may optionally wait for an additional time period (e.g. if the queuing delay is minimal) to ensure that any resources allocated in and by the SMLC have time to be released. The VMSC may then send another location service request to the SMLC or BSC associated with the current serving cell of the target MS. Abort the Location Service This action shall be employed for any event that permanently impedes a location service attempt, such as loss of the DCCH to the target MS. When such an event is notified to the VMSC, it shall cancel the current location service attempt and the associated BSSMAP-LEor BSSMAP dialogue with the SMLC (NSS based SMLC) or BSC (BSS based SMLC), respectively, if still existing, by sending a BSSMAP-LE or BSSMAP Perform Location Abort message to the SMLC or BSC, respectively. The Abort message shall contain the reason for the location procedure cancellation. The VMSC shall then return an error response to the client or network entity from which the location request was originally received. The VMSC shall also release all resources (e.g. DCCH) specifically allocated for the location attempt. The following table indicates the appropriate error recovery procedure for certain events. For events not listed in the table, the VMSC need take no action. Table 2: LCS Error Recovery Procedures in the VIUISC for certain Events Event VIUISC Error Recovery Release of radio channel to the MS Abort Any error response from the SMLC or BSC except for intra-BSC, inter-BSC or inter-MSC handover Abort An error response from the SMLC indicating intra-BSC handover Restart with no additional delay required Inter-BSC Handover Restart after handover completed Inter-MSC Handover Restart after handover completed If a location service request is aborted due to an error response from the SMLC or BSC indicating congestion, the MSC may reduce the frequency of location service requests to this SMLC or BSC according to the rules in GSM 09.31, which give precedence to location service requests with a higher priority. 7.11.3 Procedures in an LMU An LMU shall return an error indication to its controlling SMLC when location measurements previously ordered by the SMLC cannot be provided due to any error condition. £75/ (GSM 03.71 version 8.0.0 Release 1999) 64 ETSI TS 101 724 V8.0.0 (2000-10) 7.1 1 .4 Procecdures in the BSC 7.11.4.1 General Procedures The BSC serving a target MS shall supervise any network or MS location service procedure, including transfer of positioning assistance data to an MS, and shall only allow one such procedure to be active at any time. If a new procedure is instigated by the SMLC for any target MS, the BSC shall cancel any previous procedure without notifying the SMLC or target MS. The new procedure shall then be treated according to the prevailing conditions - e.g. may be rejected if a previous TOA handover attempt was not yet completed. If a location information transfer to an MS initiated by an SMLC is not active, the BSC shall discard any RRLP message or message segment received from the MS. This precludes the initiation of any location service procedure from an MS. Depending on the location procedure and its current state of execution, a serving BSC may chose to defer certain radio related events (e.g. handover) to avoid interference with location - refer to the later clauses for each position method. A serving BSC shall abort all existing location related procedures for a particular target MS without notifying an NSS based SMLC or target MS if the DCCH to the target MS or the SCCP connection to the VMSC or a BSS based SMLC is released. In the event of an abort with a BSS based SMLC, the BSC shall attempt to notify the SMLC using a BSSMAP-LE Perform Location Abort. 7.1 1 .4.2 Rejection of an SMLC Positioning Request The BSC may reject any request from an SMLC for positioning or transfer of assistance data for a target MS if the request cannot be performed for reasons other than interaction with handover or other RR management. If the request is rejected, the BSC shall return a BSSLAP Reject to the SMLC containing the cause of rejection. 7.1 1 .4.3 Interaction with Inter-BSC or Inter-IVISC Handover The BSC shall reject any request from an SMLC for positioning or transfer of assistance data while an inter-BSC or inter-MSC handover procedure is ongoing and shall return a BSSLAP Abort to the SMLC. The BSC shall terminate any network or MS positioning procedure or any transfer of RRLP assistance data already in progress if inter-BSC or inter-MSC handover is needed and is not precluded by the particular location procedure and its current state. When a location procedure is terminated, the BSC shall return a BSSLAP Abort message to the SMLC after the BSSMAP Handover Required has been sent to the serving MSC. The BSSLAP Abort shall contain the cause of the location procedure failure. 7.1 1 .4.4 Interaction with Intra-BSC Handover and other RR Management Procedures The BSC shall reject any request from an SMLC for positioning or transfer of assistance data while an intra-BSC handover or other intra-BSC RR management procedure involving the target MS is ongoing and shall return a BSSLAP Reset to the SMLC when the handover or other RR management procedure is complete or has timed out in the BSC. The BSC shall terminate any network or MS positioning procedure or any transfer of RRLP assistance data already in progress if an intra-BSC handover or other intra-BSC RR management procedure is needed and is not precluded by the particular location procedure and its current state. When location procedure is terminated, the BSC shall return a BSSLAP Reset message to the SMLC after the intra-BSC handover or other RR management procedure is complete or has timed out in the BSC. The BSSLAP Reset shall contain a cause indication, the current serving cell identity and may contain measurement information for the target MS (e.g. TA value). 7.1 1 .4.5 Priority of Handover and Other RR Management Procedures If the transfer of RRLP messages between an SMLC and target MS is interrupted by intra-BSC handover, inter-BSC handover or any other intra-BSC RR management procedure, the BSC shall avoid delay to the handover or RR management procedure by employing the preemption capability defined in GSM 04.06 and 04.08. This allows an RR Handover Command or other RR management command sent to the target MS to be assigned a "high" priority at the data link level enabling preemption of "low" priority RR Application Information messages (carrying RRLP messages) which may have been sent earlier. This procedure ensures that any RRLP data still untransmitted to the MS will be preempted (and discarded) by the data link layer in the BTS prior to transmission of the Handover Command or other RR Management command. £75/ (GSM 03.71 version 8.0.0 Release 1999) 65 ETSI TS 101 724 V8.0.0 (2000-10) 7.1 1 .4.6 Interaction with Segmentation When requested to transfer a segmented RRLP message between an SMLC and target MS, the BSC shall discard all received RRLP segments if the transfer procedure in the BSC cannot be supported or is aborted. The BSC need not wait until all RRLP segments are received before notifying the SMLC of the failure of the RRLP procedure with a BSSLAP Abort, Reject or Reset message. If a location service procedure for a target MS is not currently underway or previously failed, the BSC shall discard all BSSLAP segments received from an SMLC for this MS until it receives the first or only segment of a new BSSLAP message. Once a location service procedure has been started involving RRLP message transfer to a target MS, the BSC shall discard all RRLP segments received from the MS until it receives the first or only segment of a new RRLP message. The new RRLP message shall then be treated according to the state of the RRLP message transfer as described in clause 7.7. Further details regarding transfer and segmentation of RRLP messages between a BSC and MS can be found in GSM 04.08. 7.11.4.7 Overload The BSC may indicate an inability to support location due to overload by rejecting with a cause indicating congestion a BSSMAP Perform Location request received from the MSC. If a BSS based SMLC has rejected a request from the BSC to perform location with a cause indicating congestion, the BSC shall convey the rejection and cause to the MSC if the request was MSC initiated. If the request was initiated by the BSC, the BSC may reduce the frequency of its location requests to the SMLC according to the rules in GSM 09.31, which give precedence to location service requests with a higher priority. 7. 11 .5 Procedures in the Target MS A target MS shall terminate any positioning procedure or the transfer of RRLP positioning assistance data without sending any response to the SMLC if any RR message is received from the BSC that starts some other RR management procedure, including a new positioning procedure. The new RR procedure shall then be executed by the MS. 7.1 1 .6 Further ProcecJures for Handover 7.1 1 .6.1 MSC procedure for Inter-MSC Handover When a location estimate is required for a target MS with an established call in a state of inter-MSC handover, the serving cell ID or serving location area ID shall be used by the visited MSC to identify the correct SMLC to perform the location. All layer-3 BSSMAP and DTAP Location request related messages that are transferred over the A- interface shall now be sent via MAP/E interface piggy-backed in MAP_FORWARD_ACCESS_SIGNALLING and MAP PROCESS_ACCESS_SIGNALLING between the visited and serving MSCs. 7.1 1 .6.2 Handling of an ongoing handover while a request for positioning arrives at MSC/VLR If during an ongoing radio handover procedure a request for location information arrives at the MSCA'^LR, the request shall be suspended until the HANDOVER COMPLETE message is received at the MSC/VLR. On completion of the handover, the MSC/VLR shall issue continue with location preparation procedure. 7.12 Privacy 7.12.1 Privacy Override Indicator (POI) The POI is used to determine whether the privacy settings of the subscriber to be positioned shall be overridden by the request for location services. The assignment of a POI value with an 'override' or 'not override' value in the LCS client profile is done during the LCS client provisioning. The type of LCS client requesting location information (i.e. emergency, law-enforcement etc.) shall determine the value of the POI assigned to the LCS client profile. £75/ (GSM 03.71 version 8.0.0 Release 1999) 66 ETSI TS 101 724 V8.0.0 (2000-10) There are two distinct cases regarding the handling of the privacy override indicator. Procedure A: If the subscriber to be positioned is in the same PLMN or same country as the GMLC then the POI shall override the subscriber's privacy options. Procedure B: Otherwise the POI shall not override the subscriber's privacy options. 7.12.2 Privacy Procedures The SLPP shall contain the privacy options defined in the HLR of the MS subscriber. The SLPP shall be downloaded to the VMSC together with the rest of his subscription information in the existing MAP operation INSERT_SUBSCRIBER_DATA. It will be deleted with the existing MAP operation DELETE_SUBSCRIBER_DATA. The POI is transferred from the GMLC to the VMSC in the location request. Based on the location of the GMLC the VMSC evaluates whether to accept or ignore the received POI according to the definition in Clause 6.6. L If the POI is accepted the location requested is unconditionally performed. Otherwise if the POI is ignored the VMSC evaluates the privacy options in the MS subscriber's subscription profile (assuming this is held in the VLR). If the VLR does not contain the MS subscription profile, LCS will rely on the existing GSM recovery mechanisms to obtain the profile. If the location request is allowed by the privacy options the location request is performed. Otherwise, if the location request is barred by the privacy options, the location request is refused an error response is returned to the GMLC with a cause code indicating that the request was rejected by the subscriber. 7.12.3 MS Privacy Options The MS privacy options in the SLPP apply to an MT-LR or NI-LR and either indicate that no MT-LR or NI-LR is allowed for the MS (except as may be overridden by the POI or local regulatory requirements) or define the particular classes of LCS client for which an MT-LR or NI-LR for location are allowed, with the following classes being possible: a) Universal Class - allow positioning by all LCS clients b) Call related Class - comprises any LCS client to which the MS originated a call that is currently established. For all clients in the call related class, one of the following subscription options shall apply: positioning allowed without notifying the MS user (default case); positioning allowed with notification to the MS user; positioning requires notification and verification by the MS user; positioning is allowed only if granted by the MS user or if there is no response to the notification; positioning requires notification and verification by the MS user; positioning is allowed only if granted by the MS user; c) Non-Call related Class - allow positioning by specific identified LCS Clients or groups of LCS Client with the following restrictions allowed for each identified LCS Client or group of LCS Clients Location request allowed only from GMLCs identified in the SLPP Location request allowed only from a GMLC in the home country Location request allowed from any GMLC For each identified value added LCS client in the privacy exception list one of the following subscription options shall apply: positioning allowed without notifying the MS user (default case); positioning allowed with notification to the MS user; £75/ (GSM 03.71 version 8.0.0 Release 1999) 67 ETSI TS 101 724 V8.0.0 (2000-10) positioning requires notification and verification by the MS user; positioning is allowed only if granted by the MS user or if there is no response to the notification; positioning requires notification and verification by the MS user; positioning is allowed only if granted by the MS user; For all value added LCS clients sending a non-call related MT-LR that are not identified in the privacy exception list, one of the following subscription option shall apply: positioning not allowed (default case); positioning allowed with notification to the MS user; positioning requires notification and verification by the MS user; positioning is allowed only if granted by the MS user or if there is no response to the notification; positioning requires notification and verification by the MS user; positioning is allowed only if granted by the MS user; d) PLMN operator Class - allow positioning by specific types of client within or associated with the VPLMN, with the following types of client identified: clients providing a location related broadcast service - O&M cUent in the HPLMN (when the MS is currently being served by the HPLMN) - O&M chent in the VPLMN Clients recording anonymous location information without any MS identifier Clients enhancing or supporting any supplementary service, IN service, bearer service or teleservice subscribed to by the target MS subscriber If the MS subscribes to the universal class, any MT-LR or NI-LR shall be allowed by the VMSC. If local regulatory requirements mandate it, any MT-LR for an emergency services LCS client and any NI-LR for an emergency services call origination shall be allowed by the VMSC. If the MS subscribes to the call-related class, an MT-LR may be allowed if the MS previously originated a call that is still established and the called party number either dialed by the MS or used by the VMSC for routing matches the called party number received from the GMLC. If the called party number conditions are satisfied, the MT-LR shall be allowed if the MS user subscribes to either location without notification or location with notification. If the MS user subscribes to location with notification and privacy verification, the MT-LR shall be allowed following notification to the MS if the MS user either returns a response indicating that location is allowed or returns no response but subscribes to allowing location in the absence of a response. In all other cases, the MT-LR shall be restricted. If the MS subscribes to the non-call related class, an MT-LR may be allowed by the network if the identity of the LCS client or LCS client group supplied by the GMLC matches the identity of any LCS Client or LCS Client group contained in the MS's SLPP and any other GMLC restrictions associated with this LCS Client identity in the SLPP are also met. If the LCS client is correctly matched in this way and any GMLC restrictions are satisfied, the MT-LR shall be allowed if the MS user subscribes to either location without notification or location with notification. If the MS user subscribes to location with notification and privacy verification, the MT-LR shall be allowed following notification to the MS if the MS user either returns a response indicating that location is allowed or returns no response but subscribes to location in the absence of a response. In all other cases, the MT-LR shall be restricted. If the MS subscribes to the non-call related class, an MT-LR from an LCS client that is not contained in the MS's SLPP shall allowed or restricted according to the following conditions. For any non-matched LCS client, the MT-LR shall be allowed if the MS user subscribes to location with notification. If the MS user subscribes to location with notification and privacy verification, the MT-LR shall be allowed following notification to the MS if the MS user either returns a response indicating that location is allowed or returns no response but subscribes to location in the absence of a response. In all other cases, the MT-LR shall be restricted. If the MS subscribes to the PLMN class, an NI-LR or MT-LR shall be allowed if the client within the VPLMN, for an NI-LR, or the client identified by the GMLC, for an MT-LR, either matches a generic type of client contained in the MS's SLPP or is otherwise authorized by local regulatory requirements to locate the MS. £75/ (GSM 03.71 version 8.0.0 Release 1999) 68 ETSI TS 101 724 V8.0.0 (2000-10) In evaluating privacy where any address "A" associated with the LCS client (e.g. LCS client ID or GMLC address) needs to be compared with a corresponding address "B" in the target MS's SLPP, a match shall be determined if a match is found for each of the following components of each address: a) Numbering Plan b) Nature of Address Indicator c) Corresponding address digits for all digits in "B" (the digits or initial digits in "A" must match all the digits in "B", but "A" may contain additional digits beyond those in "B") All addresses shall be transferred to the MSC/VLR in international format. 7.13 Mobile Originating Location An MS may subscribe to any of the following classes of mobile originating location: A) Basic Self Location B) Autonomous Self Location C) Transfer to Third Party An MO-LR shall be allowed by the VMSC if the type of request is supported by the appropriate subscription according to the following table. Table 3: Required IVIS Subscription Options for lUIO-LR Requests Type of MO-LR Request Required MS Subscription MS requests own location Basic Self Location MS requests location assistance data Autonomous Self Location MS requests transfer of own location to another LCS Client Transfer to Third Party 7.14 CIV! Procedures 7.14.1 Location request for a mobile in idle-mode When a request for location information is received at the VMSC the LCS-layer shall order paging of the MS subscriber. In case of first unsuccessful paging, normal paging procedures should apply. After successful paging the LCS-layer shall invoke the location preparation procedure. 7.14.2 Location request for a mobile in dedicated-mode When a request for location information is received at the VMSC, if the MS is already busy on CM level, the LCS-layer shall attempt to establish a parallel transaction to the existing one. If successful, the LCS-layer shall invoke the location preparation procedure. 7.15 Radio Interface Timing Procedures The Radio Interface Timing determination system consists of functions in LMUs and in the SMLC. The system runs continuously offering base station synchronization information for mobile station location. £75/ (GSM 03.71 version 8.0.0 Release 1999) 69 ETSI TS 101 724 V8.0.0 (2000-10) 7.15.1 LMU Functions The Radio Interface Timing functionality in the LMU must be capable of performing the following functions: The LMU performs necessary air interface measurements from signals transmitted by base stations (both serving and neighbor). These signals can be normal bursts, dummy bursts, and synchronization bursts on the BCCH frequency. If the LMU contains the common reference clock, it time stamps reception of BTS signals. If there is no reference clock available, the LMU makes Real Time Difference measurements, i.e. measures the time difference between arrival of bursts from two base stations (e.g. serving and one of neighbors) The LMU performs some processing of measurements, like averaging and filtering, using parameters delivered to it, or in their absence using default settings. 7.15.2 SMLC Functions The SMLC must be capable of performing the following functions related to Radio Interface Timing determination: The SMLC sends to LMUs requests for Radio Interface Timing measurement information. The SMLC will communicate continuously with LMUs; thus, the SMLC can monitor operation of LMUs. If a LMU fails to send Radio Interface Timing information, the SMLC shall try to restart the LMU, and if this restarting fails, the SMLC shall inform O&M system. SMLC can use also diagnostics messages to query the status of LMUs. The SMLC receives Radio Interface Timing measurement results from LMUs. The SMLC stores or queries extra information required for base station synchronization determination, like base station and LMU coordinates, base station identity information (LAC, CI, BSIC, carrier), and burst length schemes. The SMLC determines synchronization differences between base stations using measurements and other information. Synchronization information is delivered for mobile station location purposes. 7.15.3 LMU-SMLC Interactions The request for Radio Interface Timing measurement information from the SMLC to a LMU contains the following parameters: Measurement type. This indicates whether the SMLC wants the LMU to perform Absolute Time Difference (ATD) or Real Time Difference (RTD) measurements. Measurement result reporting frequency. This indicates how often the LMU should send Radio Interface Timing measurement results. Measurement duration. This indicates how long the LMU should make measurements and report results. Instructions about filtering of raw measurement data. Instructions about base stations to be measured. The LMU unit can measure autonomously a certain number of most strongly received base stations. Another possibility is that the SMLC tells which base stations it should measure. If the LMU measures signals from BTSs from other time slots than or 4, it must be informed about the burst length scheme used by BTSs. £75/ (GSM 03.71 version 8.0.0 Release 1999) 70 ETSI TS 101 724 V8.0.0 (2000-10) The Radio Interface Timing measurement response from a LMU to the SMLC contains: Location Area Code and Cell Identity of the serving base station. If the LMU can perform ATD measurements, and it is told to do them, the ATD measurement of the serving BTS is reported (i.e. time stamp for the reception of the burst from the serving BTS referred to the common reference clock). Time slot number of the burst(s) measured from the serving BTS. Frame number of the (last) burst measured from the serving BTS. For each measured neighbor BTS its identity as Location Area Code and Cell Identity or BSIC & carrier. For each measured neighbor BTS the possible ATD measurement is reported. This can be expressed relative to the ATD value of the serving BTS. If the LMU does not perform ATD measurements, for each measured neighbor BTS, Observed Time Difference value between the receptions of signals from the serving and the neighbor BTS is reported. For each measured neighbor BTS the time slot number of its burst(s). For each measured neighbor BTS the (last) frame number of its burst. For each measured BTS the quality of measurements. Also the RX level can be reported. 8 TA based Positioning 8.1 Definition of TA states 8.1.1 MS in IDLE State In IDLE state the GSM MS may be paged or may request an originating (e.g. emergency) call. The paging response message or CM Service Request, in each case respectively, received in COMPLETE_LAYER_3 message may contain location information that includes the TA value. If available, the TA value and other location information shall be provided to the SMLC by the requesting VMSC or BSC along with the current serving cell ID in the BSSMAP-LE Perform Location request (see clause 7). The present documentables TA based positioning in the SMLC without any further interactions. 8.1 .2 MS in DEDICATED State In DEDICATED state the SMLC shall send a TA_REQUEST to request the TA value from the serving BSC. The BSC shall respond with a TA_RESPONSE carrying the TA value. The associated procedure is described in clauses 8.2 and 8.3. £75/ (GSM 03.71 version 8.0.0 Release 1999) 71 ETSI TS 101 724 V8.0.0 (2000-10) 8.2 TA Positioning Procedure for an NSS based SIVILC The TA positioning procedure for an NSS based SMLC makes use of the generic SMLC to BSC Information transfer procedure defined in clause 7. SMLC VMSC 1 . BSSMAP-LE Connection Oriented Information (TA Request) 4. BSSIVIAP-LE Connection Oriented information (TA Response) BSC 2. BSSIVIAP Connection Oriented information (TA Request) < 3. BSSMAP Connection Oriented Information (TA Response) MS Figure 50: TA Positioning Procedure for an NSS based SIVILC 1) The SMLC sends a BSSMAP-LE Connection Oriented Information message to the visited MSC serving a particular target MS. The BSSLAP APDU parameter in this message contains a TA Request. 2) The VMSC transfers the BSSMAP message received in step 1 to the serving BSC for the target MS. 3) The BSC returns the current TA value and current serving cell for the target MS to the VMSC in a TA response contained within a BSSMAP Connection Oriented Information message. The TA response may also include the latest measurement results received from the target MS for the serving and neighboring cells. 4) The VMSC forwards the BSSMAP-LE message received in step 3 to the SMLC. The SMLC then derives a location estimate for the target MS based on the received serving cell ID, TA value and other measurement results if included. 8.3 TA Positioning Procedure for a BSS based SIVILC The TA positioning procedure for a BSS based SMLC makes use of the generic SMLC to BSC Information transfer procedure defined in clause 7. SMLC BSC 1 . BSSMAP-LE Connection Oriented Information (TA Request) 4 4. BSSMAP-LE Connection Oriented Information (TA Response) MS Figure 51 : TA Positioning Procedure for a BSS based SMLC 1) The SMLC sends a BSSMAP-LE Connection Oriented Information message to the BSC serving a particular target MS. The BSSLAP APDU parameter in this message contains a TA Request. 2) The BSC returns the current TA value and current serving cell for the target MS to the SMLC in a TA response contained within a BSSMAP-LE Connection Oriented Information message. The TA response may also include the latest measurement results received from the target MS for the serving and neighboring cells. The SMLC then derives a location estimate for the target MS based on the received serving cell ID, TA value and other measurement results if included. £75/ (GSM 03.71 version 8.0.0 Release 1999) 72 ETSI TS 101 724 V8.0.0 (2000-10) 8.4 Unsuccessful TA positioning procedure in BSC There are three messages defined to handle error scenarios during positioning procedure in BSC. The messages are 1) Reject, 2) Abort and 3) Reset . Please refer to GSM 8.71 for details. After receiving the BSSLAP TA Request in BSC (message 2 in clause 8.2 and message 1 in clause 8.3), a Reject will be sent with proper cause value from BSC to SMLC in "BSSMAP Location Information Report" if TA positioning cannot be performed in BSC at that time for reasons other than handover or another ongoing RR management procedure. Between messages 2 and 3 (in clause 8.2) and between messages 1 and 2 in clause 8.3, an Abort or Reset is possible if the TA positioning cannot be done in BSC during that time. Reset is sent to SMLC to indicate when the positioning needs to be restarted after temporary interruption due to intra BSC HO or other intra-BSC RR management. Abort is used to indicate to SMLC the failure of the current TA positioning attempt (e.g. due to inter-BSC handover) and allowing a new one from application level. £75/ (GSM 03.71 version 8.0.0 Release 1999) 73 ETSI TS 101 724 V8.0.0 (2000-10) TOA based positioning After receiving the 'BSSMAP-LE Connection Oriented Information (TOA Request) ' from VMSC/SMLC, the BSC shall initiate procedures for position the MS with TOA po sitioning method. 9.1 TOA procedures 9.1 .1 Successful TOA Positioning Procedure for NSS based SMLC SMLC MSC/VLR BSC 1. BSSMAP-LE Connection Oriented Information (TOA Request) 4. BSSMAP-LE Connection Oriented Information (TOA Response) 5. DTAP-LE Register br Facility (LLP TOA Cohmand) 5. DTAP-LE Register 3r Facility (LLP TOA Conmand) 6. DTAP-LE Register or 6. DTAP-LE(Register oi 12. DTAP-LE Facility Measurement Respo 12.. DTAP-LE Facility Measurement Respo 2. BSSMAP Gonnectic Oriented Information Request) 3. BSSMAP Connectic Oriented Information r Response) 11.. DTAP-LE Facil Response) jr Release Complete ( r se) or Release Complete (l(.LP TOA r se) BIS (TOA (TOA Facility (LLP TOA Comn Facility (LLP TOA Comn 7. Handover Command Command ty or Release Complete ( TOA (L_P 1 1 . DTAP-LE Facility or Release Complete (L|LP TOA Measurement Response) LMU and) and) 10.. Handover Failure LLP TOA Measurement LMU MS t 8.. H indover Access I'^'e 9.. T!1 24 expiry Figure 52: TOA measurement flows £75/ (GSM 03.71 version 8.0.0 Release 1999) 74 ETSI TS 101 724 V8.0.0 (2000-10) Positioning Preparations: 1. VMSC receives a 'BSSMAP-LE Connection Oriented Information (TOA Request)' message from SMLC, which contains the BSC delta timer value and an indication of the preferred type of handover (intra-cell to same channel, intra-cell to new channel or inter-cell). The message also contains the cell ID and TDMA frame number of the serving cell, and depending on the preferred handover type, also contains the cell ID and TDMA frame number for candidate (maximum six) cells for positioning handover. 2. The MSC sends the BSSMAP Connection Oriented Information (TOA Request) ' message to BSC with the same information received in step 1 . 3. The BSC specifies the physical channel information (frequencies, hopping sequence, channel type, time slot for access burst etc.), cell ID, TA, measurement report, MS output power, and handover reference number in the 'BSSMAP Connection Oriented Information (TOA Response) ' message to the VMSC. The BSC also starts the delta timer. NOTE: If the BSC selects to use a different channel, this channel is reserved internally within the BSC, i.e. no additional signaling or delay is required. Based on the request information from SMLC, the BSC can choose between requesting an intra-cell handover (to same channel or to a new channel) or an inter-cell handover. If BSC decides to make an inter-cell handover the BSC selects a neighbor cell based on the measurement reports received from the MS (only neighbors for which the MS has been able to decode BSIC are possible to specify since the MS needs to know the timing of the target base station). 4. The VMSC forwards the information to the SMLC in 'BSSMAP-LE Connection Oriented Information (TOA Response) ' message. SMLC uses this information for the configuration of the LMUs. 5. The SMLC selects which LMUs should measure and sends 'DTAP-LE Register or Facility (LLP TOA Command)' messages for each of these LMUs to the MSC according to the procedure defined in clause?. 8. LL Each DTAP-LE message is targeted to one LMU and specifies Radio Frequency List, Hopping Sequence Information, HO reference number, BSIC, Starting Time, Measurement Options, Starting Time Uncertainty, GPS Time Stamping Request. 6. The MSC sends the DTAP message, which reaches the LMUs over the air interface. It has been assumed here that the DTAP connection is already established at this point (refer to clause?. 8. LI). Positioning Establishment: ?. At expiration of the delta timer (note 1), the mobile is instructed to perform non-synchronized handover from the current radio channel (e.g. SDCCH or TCH) to a specified traffic channel with HANDOVER COMMAND message. A TDMA frame number at which the sending of ACCESS burst should begin is specified. 8. The MS starts sending the access burst in HANDOVER ACCESS message. At the same time, configured LMUs measure the Time of Arrival of access bursts. 9. The MS continues to send the access bursts until the timer T3124 expires when the MS returns to the old channel. 10. The MS sends the HANDOVER FAILURE message to the BSC. 1 1 . LMUs report their measurement results in a 'DTAP-LE Facility or Release Complete (LLP TOA Measurement Response)' message to the VMSC. 12. The measurement results will be forwarded to the SMLC as a 'DTAP-LE Facility or Release Complete (LLP TOA Measurement Response)' message with measured TOA, TOA quality estimate, and Used Time Stamping. SMLC shall keep track of the number of expected measurement results from LMUs in the network. If a location estimate satisfying the requested QoS was not successfully obtained, the SMLC may initiate another TOA location attempt by restarting the TOA procedure at step 1 . NOTE 1: BSC starts the delta timer when received from the MSC in (2). The purpose of this timer is to allow enough time for MLC to initialize and configure all the LMUs for the TOA measurement. This timer value should be long enough for this task. When the BSC timer runs out, the BSC starts the handover process (step?). £75/ (GSM 03.71 version 8.0.0 Release 1999) 75 ETSI TS 101 724 V8.0.0 (2000-10) NOTE 2: After a radio channel is allocated to the MS to be positioned, the MS starts sending measurement reports to the serving BTS. Based on these measurement reports the BSC would normally order handovers when considered necessary. If a radio related handover would take place between message 1 and 7, this would invalidate the information sent to the LMUs and positioning would fail. After the initialization of the delta timer in the BSC (step 3), the BSC shall cancel the ongoing positioning if a radio related handover has been requested. On the other hand, the BSC shall never allow any radio-related handover during steps 7 to 10. 9.1 .2 Successful TOA Positioning Procedure for BSS based SMLC SMLC BSC BTS LMU LMU MS w 1. BSSMAP-LE Connection Oriented Information (TOA Request) ^ ^ 2. BSSMAP-LE Connection Oriented Information (TOA Response) h 3. DTAP-LE Register or Facility (LLP TOA Command) w h ^ P 3. DTAP-LE Register or Facility (LLP TOA Command) ^ k~ w w 4. Handover Command Command ^ ^ ^ ^ ^ ^ -^ ^ 5. Handover Acci iSS ^ ^ 6. T31 24 expiry ^ ^ ^ ^ 7. Handover Failure -^ ^ 8. DTAP-LE Facility or Release Complete LLP TOA Measurement ^esponse)t ^ 8. DTAP-LE Facility or Release Complete LLP TOA Measurem 3nt tesponse) Figure 53: TOA measurement flows for BSS based SIUILC Positioning Preparations: 1. BSC receives a 'BSSMAP-LE Connection Oriented Information (TOA Command)' message from SMLC, which contains the BSC delta timer value and an indication of the preferred type of handover (intra-cell to same channel, intra-cell to new channel or inter-cell). The message also contains the cell ID and TDMA frame number of the serving cell, and depending on the preferred handover type, also contains the cell ID and TDMA frame number for candidate (maximum six) cells for positioning handover. 2. The BSC specifies the physical channel information (frequencies, hopping sequence, channel type, time slot for access burst etc.), cell ID, TA, measurement report, MS output power, and handover reference number in the 'BSSMAP-LE Connection Oriented Information (TOA Response)' message to the SMLC. The BSC also starts the delta timer. SMLC uses this information for the configuration of the LMUs £75/ (GSM 03.71 version 8.0.0 Release 1999) 76 ETSI TS 101 724 V8.0.0 (2000-10) NOTE: If the BSC selects to use a different channel, this channel is reserved internally within the BSC, i.e. no additional signaling or delay is required. Based on the request information from SMLC, the BSC can choose between requesting an intra-cell handover (to same channel or to a new channel) or an inter-cell handover. If BSC decides to make an inter-cell handover the BSC selects a neighbor cell based on the measurement reports received from the MS (only neighbors for which the MS has been able to decode BSIC are possible to specify since the MS needs to know the timing of the target base station). 3. The SMLC selects which LMUs should measure and sends 'DTAP-LE Resister or Facility (LLP TOA Command)' messages for each of these LMUs according to the procedure defined in clause 7.8.4. lEach LCS Information Request message is targeted to one LMU and specifies Radio Frequency List, Hopping Sequence Information, HO reference number, BSIC, Starting Time, Measurement Options, Starting Time Uncertainty, GPS Time Stamping Request. It has been assumed here that the DTAP connection is already established at this point (refer to clause 7.8.4.1). Positioning Establishment: 4. At expiration of the delta timer (note 1), the mobile is instructed to perform non-synchronized handover from the current radio channel (e.g. SDCCH or TCH) to a specified traffic channel with HANDOVER COMMAND message. A TDMA frame number at which the sending of ACCESS burst should begin is specified. 5. The MS starts sending the access burst in HANDOVER ACCESS message. At the same time, configured LMUs measure the Time of Arrival of access bursts. 6. The MS continues to send the access bursts until the timer T3124 expires when the MS returns to the old channel. 7. The MS sends the HANDOVER FAILURE message to the BSC. 8. The measurement results will be forwarded to the SMLC as a 'DTAP-LE Facility or Release Complete (LLP TOA Measurement Response)' LCS Information Response message with measured TOA, TOA quality estimate, and Used Time Stamping. SMLC shall keep track of the number of expected measurement results from LMUs in the network. NOTE 1: BSC starts the delta timer when received from the SMLC in (1). The purpose of this timer is to allow enough time for SMLC to initialize and configure all the LMUs for the TOA measurement. This timer value should be long enough for this task. When the BSC timer runs out, the BSC starts the handover process (step 4). NOTE 2: After a radio channel is allocated to the MS to be positioned, the MS starts sending measurement reports to the serving BTS. Based on these measurement reports the BSC would normally order handovers when considered necessary. If a radio related handover would take place between message 1 and 4, this would invalidate the information sent to the LMUs and positioning would fail. After the initialization of the delta timer in the BSC (step 2), the BSC shall cancel the ongoing positioning if a radio related handover has been requested. On the other hand, the BSC shall never allow any radio-related handover during steps 4 to 7. 9.1 .3 Successful TOA positioning procedure in BSC There are three messages defined to handle error scenarios during positioning procedure in BSC. The messages are 1) Reject, 2) Abort and 3) Reset . Please refer to GSM 8.71 for details. After receiving the BSSLAP TOA Command in BSC (message 2 in clause 9.1.1 and message 1 in clause 9.1.2), a Reject will be sent with proper cause value from BSC to SMLC in "BSSMAP Location Information Report" if TOA positioning cannot be performed in BSC at that time for reasons other than handover or another ongoing RR management procedure. Between messages 3 and 7 in clause 9.1.1 and between messages 2 and 4 in clause 9.1.2 (i.e the duration of delta timer in the BSC), an Abort or Reset is possible if the TOA positioning can not be done in BSC during that time. Reset is sent to SMLC to indicate when the positioning needs to be restarted after temporary interruption due to an intra BSC HO or other intra-BSC RR management procedure. If the Handover Complete or Handover Failure is not received before the delta timer expires. Abort may be sent at the expiration of delta timer from BSC to SMLC. Abort is used to indicate to SMLC the failure of the current TOA positioning attempt (e.g. due to inter-BSC handover) and allowing a new one from application level. £75/ (GSM 03.71 version 8.0.0 Release 1999) 77 ETSI TS 101 724 V8.0.0 (2000-10) 10 E-OTD and GPS Positioning Procedures 10.1 General Procedures For any location request where the highest priority level is assigned and MS-based GPS positioning is not used, the SMLC shall provide sufficient assistance data to a target MS to enable a location estimate or location measurements to succeed according to the required QoS on the first attempt. The SMLC shall not assume in this case that the target MS already possesses assistance data. For a lower priority location request or when MS-based GPS positioning is used, the SMLC may reduce the assistance data provided to a target MS on the first location attempt. For these cases, clauses 10.2 and 10.3 indicate what reduced assistance data may be provided. 1 0.2 Positioning for BSS based SIVILC This signaling flow is generic for all MS based or assisted location methods (MS Based E-OTD, MS Assisted E-OTD, GPS and Assisted GPS). SMLC BSC 1. RRLP Measure Position Request MS 2. RRLP IVIeasure Position Request 3. RRLP IVIeasure Position Response 4. RRLP Measure Position Response Figure 54: E-OTD/GPS Positioning Flow 1. The SMLC determines possible assistance data and sends RRLP MEASURE POSITION REQUEST to the BSC. 2. The BSC forwards the positioning request including the QoS and any assistance data to the MS in a RRLP MEASURE POSITION REQUEST. 3. The MS performs the requested E-OTD or GPS measurements, if needed assistance data is available in the MS. If the MS is able to calculate its own location and this is required and needed assistance data is available in MS, the MS computes a location estimate based on E-OTD or GPS measurements. In case of E-OTD, any data necessary to perform these operations will either be provided in the RRLP MEASURE POSITION request or available from broadcast sources. In case of Assisted GPS and first positioning attempt. Acquisition Assistance data and optionally Differential GPS data will be provided in the RRLP MEASURE POSITION REQUEST. In case of MS based GPS and further positioning attempt (failure in first attempt due to missing assistance data), complete GPS assistance data excluding Acquisition Assistance data will be provided in the RRLP MEASURE POSITION REQUEST. The resulting E-OTD or GPS measurements or E-OTD or GPS location estimate are returned to the BSC in a RRLP MEASURE POSITION RESPONSE. If the MS was unable to perform the necessary measurements, or compute a location, a failure indication identifying the reason for failure (e.g. missing assistance data) is returned instead. 4. BSC forwards the RRLP MEASURE POSITION response to SMLC. 1 0.3 Positioning for NSS based SIVILC This signaling flow is generic for all MS based or assisted location methods (MS Based E-OTD, MS Assisted E-OTD, GPS and Assisted GPS). £75/ (GSM 03.71 version 8.0.0 Release 1999) 78 ETSI TS 101 724 V8.0.0 (2000-10) SMLC MSC 1. RRLP Measure Positioi Request 6. RRLP Measure Positio i Response BSC 2. RRLP Measure Position Request 5. RRLP Measure Position Response MS 3. RRLP Measure Position Request 4. RRLP Measure Position Response Figure 55: E-OTD/GPS Positioning Flow 1. The SMLC determines possible assistance data and sends RRLP MEASURE POSITION REQUEST to MSC. 2. The MSC forwards the RRLP MEASURE POSITION REQUEST to the BSC. 3. The BSC sends the positioning request including the QoS and any assistance data to the MS in a RRLP MEASURE POSITION REQUEST. 4. The MS performs the requested E-OTD or GPS measurements, if needed assistance data is available in MS. If the MS is able to calculate its own location and this is required and needed assistance data is available in MS, the MS computes an E-OTD or GPS location estimate. In case of E-OTD, any data necessary to perform these operations will be either provided in the RRLP MEASURE POSITOIN request or available from broadcast sources. In case of Assisted GPS and first positioning attempt. Acquisition Assistance data and optionally Differential GPS data will be provided in the RRLP MEASURE POSITION REQUEST. In case of MS based GPS and further positioning attempt (failure in first attempt due to missing assistance data), complete GPS assistance data excluding Acquisition Assistance data will be provided in the RRLP MEASURE POSITION REQUEST. The resulting E-OTD or GPS measurements or E-OTD or GPS location estimate are returned to the BSC in a RRLP MEASURE POSITION RESPONSE. If the MS was unable to perform the necessary measurements, or compute a location, a failure indication identifying the reason for failure (e.g. missing assistance data) is returned instead. 5. BSC sends measurement results in the MEASURE POSITION RESPONSE within BSSMAP Location Information Report message to MSC. 6. MSC forwards the measurement results in the MEASURE POSITION RESPONSE within LCS Information Report message to SMLC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 79 ETSI TS 101 724 V8.0.0 (2000-10) 1 0.4 Assistance Data Delivery from BSS based SIVILC This signaling flow is generic for all MS based location methods (MS Based and Assisted E-OTD and Network Based and Assisted GPS). SMLC BSC 1. RRLP Assistance Data MS 2. RRLP Assistance Data 3. RRLP Assistance Data Ack. 4. RRLP Assistance Data Ack. Figure 56: E-OTD or GPS Assistance Data Delivery Flow with BSS based SMLC 1) The SMLC determines assistance data and sends it in the RRLP ASSISTANCE DATA message to the BSC. 2) The BSC forwards the assistance data to the MS in a RRLP ASSISTANCE DATA message. 3) The MS acknowledges the reception of complete assistance data to the BSC with a RRLP ASSISTANCE DATA Ack. 4) The BSC forwards the RRLP ASSISTANCE DATA Ack message to the SMLC. 10.5 Assistance Data Delivery from NSS based SIVILC This signaling flow is generic for all MS based location methods (MS Based and Assisted E-OTD and Network Based and Assisted GPS). SMLC MSC 1 . RRLP Assistance Data ► 6. RRLP Assistance Data < BSC 2. RRLP Assistance Data 5. RRLP Assistance Data Ack. Ack. MS 3. RRLP Assistance Data 4. RRLP Assistance Data Ack. Figure 57: E-OTD or GPS Assistance Data Delivery Flow with NSS based SMLC 1) The SMLC determines assistance data and sends the RRLP ASSISTANCE DATA message to the MSC. 2) The MSC forwards the RRLP ASSISTANCE DATA message to the BSC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 80 ETSI TS 101 724 V8.0.0 (2000-10) 3) The BSC sends the assistance data to the MS in a RRLP ASSISTANCE DATA message. 4) The MS acknowledges the reception of complete assistance data to the BSC in a RRLP ASSISTANCE DATA Ack. 5) The BSC sends the RRLP ASSISTANCE DATA Ack to the MSC. 6) The MSC forwards the RRLP ASSISTANCE DATA Ack to the SMLC. 10.6 Error Han(dling for E-OTD and GPS This clause describes error handling for positioning and transfer of assistance data for E-OTD and GPS. For a description of error handling involving segmentation, refer to clause 7. H .4. Case 1 : When the RRLP request comes to BSC for E-OTD and GPS, The BSC will send a BSSLAP reject message to SMLC if the request cannot be supported in the BSC for reasons other than an ongoing intra BSC or inter BSC handover or other ongoing RR management procedure. For an ongoing intra BSC HO or other RR management procedure, the BSC shall return a BSSLAP Reset when the handover or RR management procedure is complete. The SMLC may then start the RRLP request (if there is time) again. For ongoing inter-BSC HO, the SMLC shall return a BSSLAP Abort. The location service request may then restart from either the LCS Client or VMSC). Case 2: When the RRLP request comes to BSC from SMLC, BSC sends the "RRLP request" to the MS if there is no ongoing HO or other RR management procedure at that point. If an intra-BSC HO or other RR management procedure is initiated in BSC, the BSC sends the HO or other RR management command to MS. A timer will then be started in BSC, the duration of which is network dependent, but typically 6 (six) seconds. Upon receiving the HO of other RR management command, the MS will stop the location procedure and start on handover or other RR management procedure, since this has higher priority than location. The MS will then send the HO complete or other RR management response message to BSC. When this message is received before the expiration of BSC timer, a BSSLAP Reset message will be sent to SMLC from BSC. The Reset will tell SMLC to start another location service request if there is enough time. Case 3: During intra-BSC HO or other intra-BSC RR management procedure, if a HO complete or RR management procedure completion was not received in BSC and the corresponding timer expired. In this case a reset or abort message will be sent to SMLC indicating MS timeout. The location service may then restart from either the SMLC if a reset was sent or from the LCS Client or VMSC if an abort was sent. Case 4: If an inter-BSC (or inter-MSC) handover is needed during a location procedure or if the BSC times out on an RRLP response from the target MS, the BSC shall send a BSSLAP Abort to the SMLC. The location service attempt may then be restarted from either the LCS Client or VMSC. £75/ (GSM 03.71 version 8.0.0 Release 1999) 81 ETSI TS 101 724 V8.0.0 (2000-10) 10.6.1 NSS based SMLC SIVLC 1 . RRLP Request 4. Fteject or Reset or Abort (Casel) N MSC 3. Reject or Reset or Abort (Case 1) \4 7. Reset (Case 2) OR 6'. Reset or Abort (Case 3) M 7. Abort (Case 4) < BSC 2. RRLP Request OR Intra-BSC Handover Initiated, T3103 started v 5. HO Complete N 6. Reset (Case 2) OR 5'. Reset or Abort (Case 3) OR 6. Abort (Case 4) 3'. RRLP Request 4. HOCommand OR MS ■ )(T31 03 Expired, HO complete nqt received OR i Cinter-BSC handover required or I BSC timeout on RRLP response from the i MS Figure 58 £75/ (GSM 03.71 version 8.0.0 Release 1999) 82 ETSI TS 101 724 V8.0.0 (2000-10) 10.6.2 BSS based SMLC SIVLC BSC 1. RRLP Request 2. Rejector Reset or Abort (Case 1 ) OR Intra-BSC Hardover Initiated, T3103 started X Handover attempt cxDmpleted 5. Reset (Case 2) 4. HO Complete N OR 5'. Reset or Abort (Case 3) OR 5'. Abort (Case 4) MS "Z. RRLP Request 3. HOCorrmand OR . T31 03 Expired, HO complete nJDt received OR Inter-BSC handover required or timeout on an RRLP response from BSC thelVIS Figure 59 1 0.7 Broadcast OF ASSISTANCE DATA In MS Based E-OTD, MS Based GPS and MS Assisted GPS systems, there is a need for assistance data to be broadcast to the MS. The assistance data to be broadcast for MS Based E-OTD contains the Real Time Difference (RTD) values (in case of a non-synchronized network) and Base Transceiver Station (BTS) coordinates. In addition, the broadcast data contains other information simplifying the E-OTD measurements. In GPS the broadcast of differential corrections to the MS increases the location accuracy for MS Based implementations. The broadcast of GPS navigation message bits and acquisition assistance data makes available the ephemeris data, increases the sensitivity, enables LMU- independent GPS time dissemination and assists the acquisition of satellite signal for both MS Based and MS Assisted implementations. The E-OTD assistance data to be broadcast is in compressed format where the redundant information is not included. The MS is capable to reconstruct the E-OTD assistance data using the message header information. The length of the message is depending on how many neighbors are included in the E-OTD assistance data as well as whether the redundant information can be removed from the message. The typical size of one broadcast message will be less than 82 octets. Part of the broadcast message (serving and neighbor basestation coordinates) may be ciphered. £75/ (GSM 03.71 version 8.0.0 Release 1999) 83 ETSI TS 101 724 V8.0.0 (2000-10) There are two types of broadcast GPS assistance data. One type of GPS assistance data to be broadcast is included in GPS Assistance Data message consists of GPS differential corrections. The amount of data is similar to the E-OTD assistance data, the maximum amount of satellites 12 which can be encapsulated into 71 octets GPS assistance data message. The message contains header information and the differential corrections. Part of the broadcast message (GPS differential corrections) may be ciphered. The second type of GPS assistance data to be broadcast is included in GPS Navigation Message Bits Data message consists of GPS navigation bits and acquisition assistance. One broadcast message has fixed information data length of 656 bits and the length of broadcast GPS navigation message bit message is 620 bits. The remaining 36 bits are filled with '0' and are reserved for future expansion. Part of the broadcast message (GPS navigation message bits, Doppler and code phase) may be ciphered. The contents of the broadcast message for the E-OTD and GPS assistance data is described in GTS 04.35. The support for these broadcast messages is optional for network and MS. The broadcast channel which is used to broadcast the E-OTD and GPS assistance data make use of the existing basic or extended CBCH and SMSCB DRX service. The LCS broadcast messages ( E-OTD assistance data, GPS differential corrections and GPS navigation message bits data message ) need to be either scheduled, or prioritized over other broadcast messages to avoid any delay. 1 0.7.1 Point-To-Multipoint Assistance Data Broadcast Flow This signaling flow is generic for MS Based E-OTD, MS Based GPS and MS Assisted GPS methods. The E-OTD/GPS Assistance Data Broadcast Message is created in SMLC and the whole message including the ciphered parts and parameters to control the transfer are transferred with below flow from SMLC to MS. SMSCB DRX service is used for LCS assistance data broadcast. Prior receiving the first schedule message MS should read first block of each message lot to be able to receive the LCS Broadcast Data or the schedule message. After receiving the schedule message MS should receive the LCS Broadcast Data messages according the schedule information. CBC SMLC 1. LCS Broadcast Data((lata & parameters) BSC BTS MS 2. SMSCB messages between CBC - BSC - BTS described in GSIVI 03.41 3. LCS Broadcast Data Response 4. LCS Broadcast Data(data) message from BTS to IVIS described in GSIVI 03.41 Figure 60: E-OTD/GPS Broadcast Data Flow 1. SMLC sends the complete broadcast message to CBC with LCS Broadcast Data message. This LCS Broadcast Data message contains the data to be broadcasted as well as parameters which indicate to which BTS the broadcast message is targeted and what time the broadcast should happen. LCS Broadcast Data message may also contain the SMSCB scheduling information which is broadcasted to MS in order that MS can utilize the SMSCB DRX feature specified in GSM 04.12 specification. SMSCB DRX operation is required in order that MS performance can be optimized. 2. CBC starts message transfer to BSC and BTS according to GSM 03.41. 3. LCS Broadcast Data Response message from CBC to SMLC is used to indicate that the LCS Broadcast Data has been deliverery request has been fulfilled. This message is not mandatory 4. BTS starts the message transfer to MS according to GSM 03.41. £75/ (GSM 03.71 version 8.0.0 Release 1999) 84 ETSI TS 101 724 V8.0.0 (2000-10) Implementations that have SMLC and/or CBC integrated into BSC may use other message signalling. 10.7.2 Ciphering In order for the operators to control the access to the assistance data, parts of the broadcast data may be ciphered. Ciphering is done with a specific key delivered by NW for this purpose. The deciphering keys may be requested by MS during a location update (IMSI Attach, Normal or Periodic Location Update) with the generic DTAP MO-LR Location Services Invoke command. . The Follow-On Procedure operation is used to keep the point-to-point connection between MS and NW open after location update. The deciphering keys are Location Area specific. The LCS Broadcast Data, when ciphered, will be partially ciphered according the LCS broadcast message definitions specified in GTS 04.35. The parts that will be ciphered in E-OTD LCS Broadcast Data message are neighbor RTD values, serving and neighbor BTS coordinates. For GPS the differential correction data, the navigation message bits, Doppler and code phase data are ciphered. The ciphering operation will be conducted by SMLC. The MS is capable to decipher the broadcast message (ciphered parts) using the cipher key (56 bits) delivered from NW to MS and using the Ciphering Serial Number (16 bits) included in the broadcast message. 10.7.3 Algoritinm The algorithm used for ciphering is the standard 56-bit DBS algorithm. The deciphering of broadcast messages is done in the ME. The algorithm will utilize the deciphering keys delivered during location update with MO-LR. SMLC ciphers the LCS Broadcast Data message (part of message is ciphered) using the deciphering keys (56 bits) and Ciphering Serial Number (16 bits) included in broadcast message using 56-bit DBS algorithm. The ciphered part is variable length with one bit resolution. From LCS Broadcast Data message header MS can compute what part of message is ciphered. Inputs to the 56-bit DBS algorithm are the following: 56-bit key K (deciphering key) requested with MO-LR 16-bit Ciphering Serial Number from broadcast message which is denoted here by IV (initialization vector) plaintext bits (the ciphered part of broadcast message) Encryption is done by producing a mask bit stream which is then added bit-by-bit to the plaintext data (XOR-operation) to obtain the ciphertext data. First IV is concatenated with 0-bits in order to achieve a 64-bit block Ii. This block is then encrypted by the DBS algorithm using the key K. Output is a 64-bit block Ij. This constitutes the first 64 bits of the mask bit stream. If the message is longer than 64 bits, then more bits are needed. Those are produced by encrypting I2 again by the DBS algorithm using the key K. Output is a 64-bit block I3. This constitutes the next 64 bits of the mask bit stream. This iteration is continued until enough bits are produced. The unnecessary bits from the last 64-bit block Ij are discarded. Below figure describes the first two mask bit generations and the two ciphered 64-bit blocks. £75/ (GSM 03.71 version 8.0.0 Release 1999) 85 ETSI TS 101 724 V8.0.0 (2000-10) Ciphering Serial Number(16 bits) Fill Bits (48 bits) Ciphering Key (56 bits) - I, 1st Mask Bit Stream (64 bits) ' ^ I X 1st 64-bit block of the broadcast message to be ciphered 1st 64-bit ciphered block to the broadcast message : u 2nd Mask Bit Stream (64 bits) 2nd 64-bit block of the broadcast message to be ciphered 2nd 64-bit ciphered block to the broadcast message Figure 61 : Ciphering Algorithm Decryption is done similarly. The same mask bit stream is produced. This time the mask stream bits are added bit-by-bit (XORed) to the ciphertext data bits. The result will be the plaintext data. 1 0.7.4 Deciphering key control ancJ delivery to MS The deciphering keys are needed in MS if the LCS Broadcast Data (ciphered parts) is ciphered. The deciphering keys' control system contains two keys (the Current Deciphering Key and the Next Deciphering Key) and the Ciphering Key Flag (indicating the current Ciphering Key Flag state in the location area in the time that the deciphering key set is delivered from SMLC to MS). Two Deciphering Keys are needed in order to overcome the problem of unsyncronized nature of the periodic location updates that MSs make in the location area. The SMLC controls the keys and there are following requirements related to the deciphering keys: Deciphering Key Set (Current and Next Deciphering Key, Ciphering Key Flag) are always location area specific One SMLC controls the deciphering key set changes inside the location area (valid for both BSS and NSS based LCS architecture) and in case several SMLCs in the location area then one coordinating SMLC for the deciphering key set control must be nominated (valid for BSS based architecture). The SMLC configuration is done with O&M procedures. The SMLC in NSS based LCS architecture has same functions as the coordinating SMLC in BSS based LCS architecture except sending the deciphering key set to other SMLCs (this may be supported still if needed). The SMLC in NSS based LCS architecture may support several location areas. The coordinating SMLC deliveres the new deciphering key set to the other SMLCs with SMLCPP protocol when the deciphering key set changes. The Ciphering Key Flag in the LCS Broadcast Data message is changed only when the coordinating SMLC changes the deciphering key set and delivers the new set to other SMLCs in the same location area. The SMLCs upon receiving the new deciphering key set, start using immediately the new set in the LCS Broadcast Data message. The coordinating SMLC also starts using the new set same time. £75/ (GSM 03.71 version 8.0.0 Release 1999) 86 ETSI TS 101 724 V8.0.0 (2000-10) The deciphering key set changes always following way when the new set is generated: The Next Deciphering Key comes to the Current Deciphering Key in the new set One new key is taken into use and named as the Next Deciphering Key The Ciphering Key Flag changes the state The MS may request the deciphering key set during the location update (IMSI Attach, Normal or Periodic Location Update) using the follow-on procedure defined in GSM 04.08. MS uses the DTAP MO-LR Location Services Invoke command to request the deciphering key set from the SMLC. The SMLC returns the deciphering key set to MS with DTAP MO-LR Location Services Return Result command. MS starts to use the new set immediately. The Ciphering Key Flag controls the MS key usage (Current/Next Deciphering Key) as follows: After receiving the new deciphering key set, MS starts using the new set immediately. The Ciphering Key Flag in the LCS Broadcast Data message and the one received with MO-LR should have same polarity. This means that MS starts using the Current Deciphering Key immediately. When the Ciphering Key Flag state changes in the LCS Broadcast Data message then MS starts to use the Next Deciphering Key for deciphering the broadcast message. The Next Deciphering Key becomes now the Current Deciphering Key in MS. The following figure describes the deciphering key delivery mechanism. Decryption key A used Decryption key B used Decryption key C used MS 1 makes periodic location update and requests deciphering l New Version Subject/Comment SMG#29 03.71 - R98 7.0.0 Approved at SMG#29 SMG#30 03.71 7.0.0 AOOIrl R98 7.1.0 Addition of further LCS functionality in GSM Release 98 SMG#30bis 03.71 7.1.0 A003 R98 7.2.1 Addition of further LCS functionality in GSM Release 98 (CR A002r1 was withdrawn) SMG#31 03.71 7.2.1 A005 R98 7.3.0 Corrections for LCS Open Issues SMG#31 03.71 7.2.1 A006 R98 7.3.0 Clarify provision of GPS and E-OTD assistance data to a target MS SMG#31 03.71 7.2.1 A007 R98 7.3.0 Modifications to support broadcast of GPS assistance data TSG SA#8 03.71 7.3.0 A008 R98 7.4.0 Ensure reliable privacy verification for value added LCS MT-LR - 03.71 - - R99 8.0.0 R99 version, same content as v.7.4.0 £75/ (GSM 03.71 version 8.0.0 Release 1999) 107 ETSI TS 101 724 V8.0.0 (2000-10) History Document history V.8.0.0 October 2000 Publication £75/